 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| free datasheet http:// free datasheet http:// doc nr: 3/001 59-en/lzt 720 0011 uen rev a ericsson gsm system en/lzt 720 0011 r1a rbs 2206 maintenance manual free datasheet http:// free datasheet http:// binder label 1 (1) uppgjord (?ven faktaansvarig om annan) - prepared (also subject responsible if other) nr - no. sg/era/srb/zp per olof h?glund 4/001 59-en/lzt 720 0011 uen dokansv/godk?nd - doc respons/approved kontr - checked datum - date rev file era/srb/z 2001-06-29 a n:\h\hicap_ois\manuals\relmaintenancemanual\work items\4_00159enlzt7200011r1a.doc 98 65 fontsize 10 fontsize 10 heading xxx lzn xxx xxx r-state 28 38 47 54 rbs 2206 maintenance manual ericsson gsm system en/lzt 720 0011 r1a fontsize 12 cutting mark fontsize 14 free datasheet http:// free datasheet http:// caption list document no. 2/001 59-en/lzt 720 0011 rbs 2206 maintenance manual date 2001-06-29 rev a introduction 1 safety instructions 2 tools and instruments 3 fault localisation 4 rbs field repair 5 test after repair 6 concluding routines 7 optical indicators and switches 8 preventive maintenance 9 cable connections 10 cdu connections 11 glossary 12 appendix spare parts catalogue 13 14 15 16 17 18 19 20 free datasheet http:// free datasheet http:// e rbs 2206 maintenance manual rbs 2206 maintenance manual ? ericsson radio systems ab ? all rights reserved ? en/lzt 720 0011 r1a 2001-07-03 1 (201) ? ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs 2206 maintenance manual due to continued progress in methodology, design and manufacturing, the contents of this document are subject to revision without notice. 2 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs 2206 maintenance manual contents 1 introduction ................................................................................................... 7 1.1 product overview ................................................................................... 7 1.2 rbs 2000 library overview ...................................................................7 1.3 target group ........................................................................................... 8 1.4 maintenance process overview..............................................................9 1.5 how to use this manual .......................................................................... 14 1.6 release history ....................................................................................... 15 2 safety instructions........................................................................................17 2.1 warnings..................................................................................................17 2.2 notes........................................................................................................18 2.3 beryllium oxide (beo).............................................................................19 2.4 electrical hazards....................................................................................21 2.5 batteries...................................................................................................24 2.6 working at heights .................................................................................. 26 2.7 radio frequency radiation.....................................................................28 2.8 other hazards ......................................................................................... 29 3 tools and instruments ................................................................................. 31 3.1 test equipment ...................................................................................... 31 3.2 omt kit .................................................................................................. 31 3.3 personal tool kit ..................................................................................... 33 3.4 references...............................................................................................35 4 fault localisation..........................................................................................37 4.1 introduction .............................................................................................. 37 4.2 fault lists ................................................................................................ 38 4.3 alna/tma a and alna/tma b ............................................................. 40 4.4 antenna....................................................................................................41 4.5 battery......................................................................................................45 4.6 battery temp sensor...............................................................................47 4.7 bdm or bfu ............................................................................................ 47 4.8 cdu ......................................................................................................... 50 en/lzt 720 0011 r1a 2001-07-03 3 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs 2206 maintenance manual 4.9 cdu bus/iom bus...................................................................................52 4.10 cdu cxu rxa cable and cdu cxu rxb cable...............................52 4.11 cdu rx in cable .................................................................................. 55 4.12 cxu ....................................................................................................... 58 4.13 cxu dc cable ...................................................................................... 58 4.14 cxu dtru rxa cable and cxu dtru rxb cable............................60 4.15 dxu ....................................................................................................... 64 4.16 environment...........................................................................................66 4.17 eom bus ............................................................................................... 66 4.18 epc bus/power communication loop..................................................66 4.19 external alarms ..................................................................................... 70 4.20 fan.........................................................................................................70 4.21 fcu........................................................................................................72 4.22 flash card ............................................................................................. 74 4.23 psu........................................................................................................76 4.24 psu dc cable.......................................................................................78 4.25 rbs db ................................................................................................. 81 4.26 tma cm.................................................................................................83 4.27 tma cm cable......................................................................................85 4.28 tru, dtru or atru.............................................................................85 4.29 y link.....................................................................................................89 5 rbs field repair...........................................................................................93 5.1 local/remote mode..................................................................................93 5.2 accu.......................................................................................................95 5.3 antenna feeder.......................................................................................98 5.4 bias injector.............................................................................................99 5.5 cdu ......................................................................................................... 100 5.6 cdu bus..................................................................................................102 5.7 cdu-cxu and the tru-cxu rx cables...............................................104 5.8 cdu-tru tx cables .............................................................................. 105 5.9 cnu ......................................................................................................... 106 4 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs 2206 maintenance manual 5.10 cxu ....................................................................................................... 107 5.11 dccu.....................................................................................................108 5.12 dc filter.................................................................................................109 5.13 dtru......................................................................................................111 5.14 dxu ....................................................................................................... 111 5.15 dxu backplane ..................................................................................... 112 5.16 esb cable ............................................................................................. 114 5.17 fans.......................................................................................................115 5.18 fcu........................................................................................................116 5.19 flash card ............................................................................................. 117 5.20 idb.........................................................................................................117 5.21 idm ........................................................................................................ 118 5.22 psu........................................................................................................119 5.23 psu dc cable.......................................................................................120 5.24 rx antenna feeder...............................................................................121 5.25 tma cm.................................................................................................122 5.26 tru........................................................................................................123 5.27 tru backplane......................................................................................124 5.28 tx antenna feeder ............................................................................... 125 6 test after repair............................................................................................127 6.1 preconditions ........................................................................................... 127 6.2 test call...................................................................................................127 7 concluding routines....................................................................................131 7.1 before leaving the site...........................................................................131 7.2 report of finished work..........................................................................131 7.3 repair delivery note ?? blue tag ? ..........................................................132 7.4 handling of replaced parts and rus ..................................................... 132 7.5 transport of a repairable unit................................................................134 7.6 trouble report on equipment or on this manual....................................134 8 optical indicators and switches ................................................................. 139 8.1 indicator types ........................................................................................ 139 en/lzt 720 0011 r1a 2001-07-03 5 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs 2206 maintenance manual 8.2 units with optical indicators and switches ..............................................139 8.3 accu.......................................................................................................139 8.4 cdu-f......................................................................................................140 8.5 cdu-g ..................................................................................................... 140 8.6 cxu ......................................................................................................... 141 8.7 dccu.......................................................................................................142 8.8 dtru........................................................................................................143 8.9 dxu ......................................................................................................... 144 8.10 fcu........................................................................................................146 8.11 idm ........................................................................................................ 146 8.12 psu........................................................................................................147 8.13 rbs status panel..................................................................................148 8.14 tma cm.................................................................................................149 9 preventive maintenance...............................................................................149 9.1 preventive maintenance process............................................................151 9.2 determining preventive maintenance intervals ......................................151 9.3 maintaining antenna systems ................................................................152 9.4 maintaining batteries ..............................................................................153 9.5 replacing fans .......................................................................................155 9.6 replacing door filter ..............................................................................155 9.7 performing concluding routines.............................................................156 10 cable connections......................................................................................157 10.1 power cables ........................................................................................ 157 10.2 opto cables...........................................................................................157 10.3 backplane cables..................................................................................159 11 cdu connections........................................................................................164 11.1 inserting and extracting rus.................................................................165 11.2 cdu to connection field - general ...................................................... 167 11.3 cdu to connection field rbs 2206.....................................................167 11.4 cdu antenna connection field rbs 2206 .......................................... 173 12 glossary.......................................................................................................187 6 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction 1 introduction this maintenance manual is valid for the radio base station rbs 2206 for ericsson gsm system release r8. the purpose of the manual is to provide the information necessary for ?st line maintenance. first line maintenance includes the following activities: ? repairs that entail replacement on site. only replaceable units (rus) are handled. ? preventive maintenance. the instructions apply only to the radio base station (rbs) connected to a base station controller (bsc), and it is assumed that the rbs is installed and in operation. the instructions in this manual presuppose that the replaced units are always put into operation. 1.1 product overview figure 1 rbs 2206 cabinet overview this is a brief overview of the rbs 2206. for further information about the rbs 2206, see: reference manual en/lzt 720 0008 the rbs 2206 is a member of the rbs 2000 family of indoor and outdoor rbss operating in the gsm 900, gsm 1800 and gsm 1900 frequency bands. en/lzt 720 0011 r1a 2001-07-03 7 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction the rbs 2206 is designed for indoor installation. it consists of a radio cabinet mounted on a base frame. cable entries for feeders, transmission and power cables are concentrated to the upper part of the cabinet on connection elds, which are covered by the cabinet door. 1.2 rbs 2000 library overview the user documentation for all rbs 2000 models consists of customer manuals divided to suit different process events. the library overview contains the following information for each manual: ? a short description ? the recommended target group ? the product number library overview lzn 302 73 !" # $ # % & ' # ( (% )*+ # # + $# , ,,-.( % figure 2 rbs customer documentation library this manual is part of the rbs customer documentation library shown in the gure above. 1.3 target group this manual is written for rbs 2000 eld technicians. the sub-section fault analysis from omc in the section maintenance process overview is written for the operation and maintenance centre (omc) operators. local safety regulations may require that all work (installation, repair, revision, and so on) with high-voltage equipment must be done by a quali ed or certi ed electrician only. the eld technician is expected to ? be experienced in radio and mobile communications. ? have good understanding of technical english. the required knowledge of the equipment can be acquired by following the ericsson gsm system training path for rbs 2000 eld technicians 8 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction 1.4 maintenance process overview the purpose of this chapter is to provide an overview of the maintenance process and describe how to perform the correct maintenance procedures. 1.4.1 general rbs 2000 radio base stations are administered and controlled by the bsc. there is a master/slave relationship between the bsc and the rbs, and the bsc has an overview of the status of the radio network and its resources. the bsc manages the o&m of the rbs across the abis interface. the rbs equipment is seen as an mo by the bsc. this is a way of describing the rbs, in a functional way and as a logical model, in the bsc. all o&m actions are based on this logical model structure created in the bsc. an mo does not necessarily have a one-to-one relationship with a physical unit in the rbs. the mo, describing rbs 2000 (g12), is divided into two sub-classes: ao and so. the so is the abstract sub-class of the mo that owns the hardware. the ao only handles functions. the rbs can be set in local or remote mode. local mode means that the rbs has been disconnected and isolated from the bsc, while in remote mode the rbs is controlled by the bsc. when the rbs is in remote mode, the bsc acts as a master in the bsc- rbs relationship and all rbs maintenance actions are ordered by the bsc. faults in the rbs are reported to the bsc on an mo basis. all faults reported by the mos in the rbs are stored in the bsc error log. tests on mos with rbs hardware can be ordered by a bsc operator in order to check the status of the rbs. the operator can also test the connection between the bsc and a tru in the rbs by ordering a loop test. a test pattern is passed through the loop created between the bsc and one speci c time slot in a speci ed tru. the rbs contains test and supervision functions that detect malfunctions and report them to the bsc. tests and supervision are performed on an mo basis, which means that the different mos supervise their own equipment. statistics are collected on an mo basis in the bsc, for example, the number of call setup attempts, or the number of abnormally terminated calls. en/lzt 720 0011 r1a 2001-07-03 9 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction 1.4.2 fault handling work?w # , ,/ 0 1 # % 1 + figure 3 fault handling work?w steps one and two are automatically performed by the bss. step three is performed at the omc by an operator who handles the rbs alarm with support from opi. by analysing the fault situation, the omc operator will be able to choose the appropriate action. at the rbs site, step four is performed by a eld technician, who follows the instructions in this manual. 1.4.3 fault analysis from omc this section very brie y describes a typical fault analysis process, performed from an omc. it describes procedures that have to be done before sending a eld technician to the site. " & 0 23 + # % ,/ 0 1 figure 4 fault analysis from omc 10 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction fault analysis the fault is given in plain text at the bsc. the faults are divided into class 1 and class 2 alarms. some of the alarms also indicate the suspected faulty hw unit in a, so called, ru map. field technician receives work order before writing the work order, the following questions are asked to optimise the site visit: ? is preventive maintenance scheduled at this site in the near future? ? are there any other faults at this site that have been postponed? ? are there any other reasons for sending a eld technician to the site? the work order must include information about the following: ? site location ? how to get to the site ? cabinet identity ? the suspected ru ? the error log must be included, if a logical ru is suspected to be faulty ? if the fault situation is unclear, site history must be included; for example, whether the same type of fault has been detected and repaired a few weeks earlier with the information above, the eld technician carries out the maintenance work at the site. when the maintenance work is completed, the eld technician sends a report back to the msc. en/lzt 720 0011 r1a 2001-07-03 11 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction 1.4.4 rbs maintenance process - 4 $23 # $ + $ #%# $ 4 $23+ # % 1 5 $+ # figure 5 the rbs maintenance process preparatory actions writing work order as a result of the fault analysis a work order is written. the work order includes information about site location, how to get to the site, cabinet identity, the suspected ru and site history. an error log is included if the fault is de ned as logical. note: the chapter safety instructions must be read through to ensure knowledge of potential risks prior to beginning work on the rbs equipment. the work order is analysed before personnel are sent to the site. the owchart(s) in the chapter fault localisation that concern the faulty unit(s) is read. this providesinformation on: ? selecting the spare parts and tools required at the rbs site. ? informing the omc operator if the site visit requires taking the rbs out of traf c or reduces rbs functions. to be done at the site fault tracing 12 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction the chapter fault localisation provides methods for nding the faulty unit in the rbs that causes the alarm reported to the bsc. for example, when the work order denotes that a tru is faulty, fault localisation will point out the position of the faulty tru. all alarms given in the ru maps correspond to a section in the chapter fault localisation . replacing faulty unit the chapter rbs field repair describes how to replace a faulty unit. testing the rbs is tested before the eld technician leaves the site. the chapter test after repair describes how to verify that the rbs is functioning properly. writing work report the chapter concluding routines provides information on the different administrative routines that must be performed before leaving the site. after maintenance handling of replaced units the chapter concluding routines describes which units are repairable and which are disposable and the different administrative routines connected to both. 1.4.5 fault cases the purpose of this section is to explain the different fault cases that can arise in the rbs 2000. this forms the basis for choosing between different methods when localising a detected fault. ? unambiguous indication with an indicator and an ru map. ? unambiguous indication with an ru map only. ? unit that is unambiguously indicated, but consists of several replaceable parts. ? logical ru indicated. note that the bss only pinpoints one ru in the ru map. indication with an indicator and an ru map examples of units dxu, dtru, cxu, psu and cdu method of localisation the work order states which unit is affected. when the cabinet is opened, a red fault indicator will be on in the faulty unit. if this indicator should be defective, only an rbs fault indicator will be on. in this case, the omt is used to localise the faulty unit. en/lzt 720 0011 r1a 2001-07-03 13 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction indication with an ru map examples of units rx cables method of localisation the work order states the unit concerned. the maintenance manual is used to nd out where the unit is located. indication of units that consist of several replaceable parts examples of units fan unit method of localisation the work order states which unit is affected. the omt is used to identify which parts are faulty, for example, which fan is faulty. logical ru indicated the logical ru is identi ed when it is not obvious which physical ru is faulty. for example, epc bus can be indicated, which means that anything connected to it can be faulty. examples of units cdu bus, eom bus, epc bus, y link and environment. method of localisation a systematic order of replacement is used to determine the unit that has generated the fault. the following applies to the logical ru environment this logical ru records conditions that cannot be affected from the rbs. the ru is divided into two parts: ? external power and climate (condensation, air humidity and temperature). when this ru is identi ed, the omc operator must analyse the fault to determine possible rbs repairs. the omc operator must be able to determine whether the reported fault requires maintenance personnel to respond or not. ? in the case of the fault message "indoor temperature out of safe range", the trouble may cease when local weather conditions change, that is, the sun sets or the temperature changes. alternatively, in the case of external power fault it is necessary to determine whether or not the cause of the fault is a commercial power failure, prior to dispatching maintenance. if a technician is sent, the work order must include the fault history for the rbs. 1.5 how to use this manual detailed information about the use of this manual and how to perform maintenance in the correct order, is found in the section maintenance process overview in this chapter. a brief description of the contents of each chapter of this manual is given below. 14 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction chapter brief description 1. introduction introduces this manual. 2. safety instructions describes the risks involved when working with rbs equipment. 3. tools and instruments speci ces recommended equipment. 4. fault localisation recommends actions for each suggested ru. the purpose is to nd the faulty unit so it can be replaced. 5. rbs field repair describes actions to be performed as soon as the suspected unit has been localised. 6. test after repair describes veri cation procedures for the rbs. 7. concluding routines describes administrative routines resulting from maintenance activity. 8. optical indicators and switches describes optical indicators and switches on all rus in the rbs. 9. preventive maintenance describes recommendations for preventive maintenance activities. 10. cable connections provides information about internal cabling in the rbs. 11. cdu connections provides information about antenna connections and rx/tx cabling in the rbs. 12. glossary explains terms and abbreviations. appendix spare parts catalogue catalogue of all spare parts of the rbs. 1.6 release history this is the rst release of the maintenance manual en/lzt 720 0011. en/lzt 720 0011 r1a 2001-07-03 15 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// introduction this page is intentionally left blank 16 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions 2 safety instructions this chapter shows the system used for presenting safety information. note: reduce the risk of accidents by studying all the instructions carefully before starting work. if questions arise regarding the safety instructions, contact the supervisor or the local ericsson company. where local regulations exist, these are to be followed. the safety information in this manual is a supplement to local regulations. it is the responsibility of the local project manager to make certain that local regulations are known and followed. the relevant manual (including this safety information) and speci c instructions supplied by ericsson must be followed in any work performed on the ericsson products or systems. a suf cient knowledge of english or of any of the other languages in which the manuals or instructions are printed is necessary. the safety information in the relevant manuals presupposes that any person performing work on ericsson products or systems has the necessary education, training and competence required in order to perform that work correctly. for certain work, additional training or special training may be required. for more precise information on the amount and content of the general and/or special training required for work on ericsson products or systems, please contact the supervisor or the local ericsson company. 2.1 warnings warnings are used to indicate hazardous activities. the warnings are preceded by the common hazard symbol. p002643 figure 6 hazard symbol the following three warning levels, shown here in order of urgency, are used: danger danger means that an accident may occur if the safety precautions are neglected. this type of accident is likely to be fatal. en/lzt 720 0011 r1a 2001-07-03 17 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions warning warning means that an accident may occur if the safety precautions are neglected. this type of accident may be fatal or cause serious injury. it may also damage the product. caution caution means that an accident may occur if the safety precautions are neglected. this type of accident may cause injury or damage the product. the following special symbols are used to indicate the risk of radio frequency radiation, electrical hazards and electrostatic discharge: p002644a figure 7 radio frequency radiation ,-6 figure 8 electrical hazard ,-- figure 9 electrostatic discharge warnings are used throughout this manual to alert the reader to special instructions concerning a particular task or operation that may be hazardous if performed incorrectly or carelessly. therefore, read the instructions carefully. strict compliance with the special instructions while performing a task is the best way of preventing accidents. 2.2 notes note: notes are used to call the reader s attention to key points that might otherwise be overlooked. 18 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions 2.3 beryllium oxide (beo) warning do not handle transistors and components without protection. beryllium oxide is highly toxic and may be found in transistors, and other components. hazard beryllium oxide dust is created by cha ng, ling or breakage. it is very dangerous if inhaled, even for only a few seconds. it can cause injury to skin or mucous membranes severe enough to endanger life or cause permanent injury. particles penetrating the skin through wounds or abrasions are liable to cause chronic ulcerations. symptoms of poisoning symptoms of beryllium poisoning are respiratory troubles or cyanosis (grey-blue discoloration of the skin). these symptoms may develop within a week, or after a period of several years. first aid ? a suspected inhalation of beryllium oxide should be treated immediately by a doctor at a hospital. ? wash the area thoroughly if it is suspected that beryllium oxide has been in contact with the skin or entered the skin through cuts or abrasions. this should be followed by a medical examination. components containing beryllium oxide do not store components and washers loose. do not le or machine them in any way. do not apply heat except when the components are clamped in a heat sink application. en/lzt 720 0011 r1a 2001-07-03 19 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions power transistors, diodes and thyristors warning do not carry loose components in pockets, bags or containers, or tamper with them in any way that could cause them to break or disintegrate. do not apply excessive heat during soldering. do not break open components for inspection. components containing beryllium oxide are clearly marked in the manufacturer s packing, and identi ed by attached information. ? store components in their original packing and do not mix them with other components. ? ensure that they do not become mechanically damaged. use care when replacing defective components. ? beryllium oxide is encapsulated and components are safe to handle for normal replacement purposes. heat sink washers note: not all heat sink washers contain beryllium. heat sinks containing beryllium, are individually packed when new. warning do not store washers loose. do not ?e or machine them in any way. do not apply heat, except when the components are clamped in a heat sink. ? handle with gloves or cloth when removing heat sink washers from packaging and mounting them into place in the equipment. 20 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions cathode ray tubes (crts) and ceramic applications warning do not handle broken glass with bare ngers. do not blow on exposed surfaces due to the danger of beryllium oxide. ceramic cylinders or formers containing beryllium are marked by blue colorations or black lines. they are safe to handle provided they are not damaged. if they are damaged, take precautions as with other components containing beryllium. disposal dispose of defective and/or broken beryllium components in approved containers. mark them clearly on the outside of the wrapping components contain beryllium warning never send defective and/or broken components containing beryllium oxide through the mail. instead, return them to the nearest depot by hand. 2.4 electrical hazards high voltage danger high voltage is used in the operation of this equipment. both direct contact with the mains power and indirect contact via damp items or moisture can be fatal. ? the ac installation must be carried out according to local regulations. these regulations may require the work to be carried out by a quali ed and authorized electrician. ? remove wrist watches, rings, bracelets, etc. ? switch off the power if the cabinet is damp inside. en/lzt 720 0011 r1a 2001-07-03 21 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions ? prevent damp entering the equipment during work in bad weather conditions. danger improper electrical installation may cause re or electrical shock. approved circuit breakers for the ac mains and the cable s cross sectional areas must always be selected in accordance with local laws and regulations. only a quali ed and authorized electrician is permitted to install or modify the electrical installation. cable markings caution verify that the cable markings correspond before connecting cables. faulty electric tools warning do not repair a faulty electric tool yourself. hand it over to your supervisor in exchange for a functioning tool. drilling warning do not drill holes in the radio base station. the drill bit may come into contact with live wires. ? always use insulated protective gloves, such as the lyb 1032, when drilling where live wires might be hidden. ? always use eye protectors (goggles) when drilling. flying chips and dust may get into your eyes. 22 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions thunderstorms danger avoid working on electrical installations or towers/masts during thunderstorms. thunderstorms create strong electric elds. for that reason, and to avoid direct strokes of lightning, it is essential that the equipment is properly earthed for thunderstorm conditions. 2.4.1 electrostatic discharge, esd caution sensitive components such as integrated circuits (ic) can be damaged by discharges of static electricity. electrical charges are generated by friction when a body moves, rubs against clothes, slides against a chair, when shoes rub against the oor, and when you handle ordinary plastics, etc. such charges may remain for a considerable period of time. handling of printed board assemblies and ic components always use an approved antistatic bracelet to avoid damage to components mounted on printed board assemblies. the esd wrist strap contains a resistor with an ohmic value greater than 1 m in the cable to protect the operator. the resistance value is low enough to discharge the electrostatic voltage. never replace the cable with any other cable. the esd wrist strap must be connected to earth. ericsson recommends wrist strap lyb 250 01/14. storing and transporting printed board assemblies and ic components use the original packaging. if this is not available, use a conductive material, or a special ic carrier that either short-circuits or insulates all leads of the components. en/lzt 720 0011 r1a 2001-07-03 23 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions 01_0250a figure 10 esd wrist strap lyb 250 01/14 danger to avoid potentially fatal circuits through the body to earth, wrist strap connections must include a resistor of at least 1 m . test the wrist strap regularly. 2.5 batteries batteries can be hazardous if improperly handled. special care must be used to prevent short-circuiting batteries, or loss of electrolyte. electrolyte contains potentially hazardous material. work danger read safety instructions regarding handling and connecting batteries. general precautions when working with batteries: ? remove wrist watches, rings, bracelets, etc. ? use insulated tools. ? make sure that eye wash facilities, or portable eye wash equipment, is available prior to starting work. use all the required ppe (personal protective equipment) such as: ? rubber gloves and aprons. 24 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions ? eye protection (goggles or a face shield). short-circuiting of batteries caution short circuits can cause injury or damage. although the battery voltage may be low, the released power can be extremely high. it is necessary to ensure that no metal object, such as a tool, short- circuits the batteries. if necessary, disconnect or remove the batteries before beginning work. explosive gases batteries may give off explosive gases. all battery areas must be adequately ventilated and protected from re. caution do not use open cell-lead acid batteries. they give off hazardous gases that may cause an explosion or corrosion of the equipment. the battery must be suitable for horizontal operation. overheated batteries caution excessive heat can cause the battery casings to become soft and to warp, allowing acid to escape. if the internal temperature of the cabinet exceeds + 60 c (140 f), take the following precautions: ? check that the batteries have not leaked. ? if the batteries have leaked, see the section hazardous waste material from leaks. en/lzt 720 0011 r1a 2001-07-03 25 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions hazardous waste material from leaks ensure that there are suf cient absorbers or neutralizing materials available on site, in case of spillage of hazardous substances. there is a danger of spillage occurring when installing, removing, replacing or servicing batteries. the absorbers and neutralizing materials must be suitable for the hazardous substances involved. table 1 typical neutralizers typical neutralisers baking soda (bicarbonate) nahco 3 sal soda na 2 co 3 ioh 2 o soda ash na 2 co 3 consult the battery manufacturers for speci c details of absorbers and neutralizing materials. absorbers and neutralizing products will vary, depending on country and manufacturer. 2.6 working at heights warning some working areas involve the risk of accidents caused by falling objects. for example, when working on a mast, tower or a roof, the following precautions must be taken: ? personnel working at heights must have the appropriate training and medical certi cate. ? full body safety harness and safety helmet must be used. ? adequate protective clothing is essential in cold weather. ? all lifting devices must be tested and approved. ? during work on a mast, all personnel in the area must wear helmets. 2.6.1 rules and advice for the safe use of ladders ? make sure that the ladder is undamaged and has been approved for use. ? do not overload the ladder. the following types of ladders must be guyed or otherwise secured ? leaning ladder longer than 5m. 26 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions ? free-standing ladder with a platform and knee-support, and with over 2 meters height to the platform. ? any other free-standing ladder longer than 3m. positioning the ladder 02_0354a figure 11 checking the angle ? the ladder s inclination should be approximately 1:4 (75 ). position the ladder according to its gradation indicator (if there is one) or check the angle with your elbow. ? use the ladder foot or a ladder support to reduce the risk of tipping over sideways. ? always attach extension legs to a ladder that is to be used on a sloping base. never prop up a ladder with boxes, stones or the like. ? extend the ladder completely. ? check that all four anti-slipping treads are rmly positioned on the base. en/lzt 720 0011 r1a 2001-07-03 27 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions climbing and using the ladder 01_0354a figure 12 climbing the ladder ? climb the ladder facing it. ? when you lean sideways, outward from the ladder, your navel should never be outside the edge of the ladder s frame. ? always keep 3 points of contact (two feet and one hand, two hands one foot) with the ladder when working on it. this will reduce the risk of falling. ? never climb the topmost four rungs of a ladder. if you have to climb up on a roof, the ladder should extend at least one meter above the eaves. 2.7 radio frequency radiation caution radio frequency (rf) radiation from antenna systems can endanger your health. co-ordinate with all mast users to switch off the transmitters when working with, or near, antennas. 28 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions 2.8 other hazards handling heavy goods warning read the safety chapter regarding handling of heavy goods. ? use tested and approved lifting devices only. they must only be used by trained personnel. ? always check that all parts of the lifting devices are intact. ? make sure that all lifting devices are properly stabilised or attached to xed objects such as walls or buildings before lifting. ? give clear and consistent command signals, for example ? lift ? lower ? stop ? make sure that there is never an angle of more than 90 between the straps at the point where they are attached to the lifting hook. 04_0030a maximum 90 figure 13 use long straps ? too large an angle between the lifting straps increases the strain on them and may cause them to snap. overloading, or wrong use of lifting devices in other ways, can have catastrophic consequences. en/lzt 720 0011 r1a 2001-07-03 29 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// safety instructions ? never walk under hoisted loads. ? follow local regulations for safety clothing and safety equipment for hoisting and moving goods. ? unsecured cabinets have a high centre of gravity. they can easily tip over and harm personnel. warning there is a danger of the assembly toppling over, which could cause injury to personnel or damage to the equipment. fire warning fire may spread to neighbouring rooms. when working on a radio base station you may have to open cable ducts, channels and access holes, thereby interfering with the re sectioning of the building. ? close the cable ducts and re doors (if applicable) as soon as possible. ? after completing work on cables, seal the cable ducts according to the regulations for the building. ? minimize the amount of in ammable material. ? avoid storing empty packaging material on the site. ? use a powder or carbon dioxide type of re extinguisher due to the electric nature of the equipment inside the radio base station. sharp edges warning wear protective gloves when handling the equipment. there may be sharp metal edges. 30 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// tools and instruments 3 tools and instruments this chapter describes tools and instruments required for maintenance activities. 3.1 test equipment table 2 test equipment product no. description speci cation / remark fab 801 0187 tems sw tems tems cable user ? s manual tems r320 for both 900 and 1800 mhz (dual band) antenna adapter click-in-holder, car kit fab 801 0194 tems sw tems tems cable user ? s manual tems t28 world for both 900 and 1900 mhz antenna adapter click-in-holder, car kit lpk 102 024/2 digital multimeter fluke 79 iii 3.2 omt kit the omt is used for installation, testing, site acceptance and maintenance of the rbs 2000 system. table 3 omt kit product no. description ntm 201 2289/1 omt kit -7- , " figure 14 omt kit en/lzt 720 0011 r1a 2001-07-03 31 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// tools and instruments table 4 omt kit speci cation item description qty product no. 1 c1, 9 pin d-sub connector male to female 1 rpm 113 463 2 omt user ? s manual 1 lzn 302 01 3 omt sw 1 note: the omt require a pc with operating system win 95, nt 4.0 or later. 32 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// tools and instruments 3.3 personal tool kit 6!- ," 6 - ! , " 6 ! , ," , ,6 , ,, , ,- ", " " ,! , - figure 15 tool set, maintenance tools note: the contents of this kit may be subject to change without notice. en/lzt 720 0011 r1a 2001-07-03 33 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// tools and instruments table 5 tool set, maintenance tools product no. description ltt 601 107/1 tool set, maintenance tools table 6 tool set, maintenance tools speci cations pos. description qty 1 tool case 1 2 side cutting pliers 1 3 snip nose pliers 1 4 adjustable spanner l=160 mm 1 5 adjustable spanner l=100 mm 1 6 slip joint pliers l=125 mm 1 7 slip joint pliers l= 245 mm 1 8 pocket survival tool 1 9 marking pen, gold colour 1 10 flexible shaft 1/4" 1 11 marking pen 1 12 1) termination tool lsy 138 252, supplier: ericsson 1 13 termination tool, supplier: krone 1 14 screwdriver l=200 mm 1 15 universal bit holder 1 16 bits kit 1 17 1) ru-extractor, button 35 mm ltd 117 13 2 18 1) ru-extractor, handle ltd 117 02 1 19 voltage tester 1 20 1) static control wrist strap lyb 250 01/14 1 21 head band for lamp holding 1 22 penlight, mini 1 23 tool rucksack 1 24 electrical tape, white 2 25 first aid kit 1 26 1) torque wrench kit 0.8 nm ltt 601 83 1 27 1) torque wrench kit 1.7 nm ltt 601 93 1 28 1) torque wrench kit 2.8 nm ltt 601 94 1 29 screwdriver, torx t8 1 30 precision screwdriver set 1 31 jumper wire (2x0.5 mm) l=10 m 1 32 extractor tool for overvoltage protector covers 1 note: 1) this part of the set can be ordered separately. 34 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// tools and instruments 3.4 references for information about general cable connections, see cabinet assembly and extension manual . for product numbers of replaceable units and other spare parts, see spare parts catalogue. table 7 product numbers of the cabinet assembly and extension manual and the spare parts catalogue product no. description en/lzt 720 00 10 cabinet assembly and expansion manual for rbs 2206 en/lzt 720 00 12 spare parts catalogue for rbs 2206 en/lzt 720 0011 r1a 2001-07-03 35 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// tools and instruments this page is intentionally left blank 36 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4 fault localisation 4.1 introduction the instructions in this chapter describe to handle fault situations that arise in the rbs. the owcharts in this chapter are for reference only. the text accompanying each owchart contains more detailed instructions. maintenance personnel should therefore only use the charts to locate the information in the text. all subsequent sections provide instructions on how to localise faults in the rbs. each title of a section corresponds to a fault code in either the so cf ru map or the so trxc ru map. these sections appear in alphabetical order. 4.1.1 preconditions information from the replacement unit map is required as input when reading this chapter. 4.1.2 work process for fault localisation the work process for fault localisation is shown below and described in brief. ,!, . $& #% ( $ + + $& & 3 $ $ # # $# . $& #% figure 16 work process for fault localisation localising the faulty cabinet the work order from the omc operator must include information stating which rbs cabinet is faulty. the faulty cabinet is also identi ed en/lzt 720 0011 r1a 2001-07-03 37 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation by the yellow rbs fault indicator, which is on when there is a fault. the rbs fault indicator is located at the left edge of the cabinet door. localising the faulty ru the work order from the omc operator also includes information stating which ru is faulty. the sections below describe the fault localisation processes relating to each faulty ru that is indicated in the fault lists. see section 4.2 on page 38. most rus are equipped with a red fault indicator. this indicator is on if a fault has been detected in the ru. rus that do not have a fault indicator, can, if faulty, only be localised by means of the omt. note: always check for a released circuit breaker on the idm, where applicable. the very rst action must always be to reset a circuit breaker, that has released. if the circuit breaker releases again, the fault localisation procedure shall continue. see chapter optical indicators and switches for the positions of all circuit breakers on the idm. repairing the rbs when the faulty ru has been identi ed, it shall be handled according to speci ed procedures. see chapter rbs field repair. checking for remaining faults when the faulty ru is replaced and the reported fault has ceased, the eld technician has to check that there are no faults remaining in the rbs. if any faults remain in the rbs, these faults have to be localised and recti ed. see the sections below in this chapter. testing after repair when all faults in the rbs have been cleared, the rbs has to be tested in order to verify that it is fully functional. see chapter test after repair. concluding routines before leaving the site, the eld technician has to go through a checklist and ll in the repair delivery note, blue tag . the routines also de ne how the faulty, replaced rus shall be treated. see chapter concluding routines. 4.2 fault lists the tables below give all faults that are treated in this chapter. these faults are indicating that a fault is found in hw. note: faults that can not be related to the rbs 2206 are excluded. 38 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.2.1 faults in the so cf ru map fault no. fault designation 0 dxu 3 y link 5 cdu 7 psu 9 bdm or bfu 12 alna/tma a 13 alna/tma b 14 battery 15 fan 20 tma cm 23 cdu rx in cable 30 cdu bus/iom bus 31 environment 33 epc bus/power communication loop 34 rbs db 35 eom bus 37 cdu cxu rxa cable 38 cdu cxu rxb cable 40 antenna 41 psu dc cable 43 flash card 45 battery temp sensor 46 fcu 47 tma cm cable 4.2.2 faults in the so trxc ru map fault no. fault designation 0 tru, dtru or atru 3 cxu tru rxa cable 4 cxu tru rxb cable en/lzt 720 0011 r1a 2001-07-03 39 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.2.3 all hw faults in alphabetical order fault designation fault no. alna/tma a so cf ru:12 alna/tma b so cf ru:13 antenna so cf ru:40 battery so cf ru:14 battery temp sensor so cf ru:45 bdm or bfu so cf ru:9 cdu so cf ru:5 cdu bus/iom bus so cf ru:30 cdu cxu rxa cable so cf ru:37 cdu cxu rxb cable so cf ru:38 cdu rx in cable so cf ru:23 cxu tru rxa cable so trxc ru:3 cxu tru rxb cable so trxc ru:4 dxu so cf ru:0 environment so cf ru:31 eom bus so cf ru:35 epc bus/power communication loop so cf ru:33 fan so cf ru:15 fcu so cf ru:46 flash card so cf ru:43 psu so cf ru:7 psu dc cable so cf ru:41 rbs db so cf ru:34 tma cm so cf ru:20 tma cm cable so cf ru:47 tru, dtru or atru so trxc ru:0 y link so cf ru:3 4.3 alna/tma a and alna/tma b note: this section will be included in the next release. 40 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.4 antenna ,! - + ! . $ # #+0 8 8 + % # , %+ #9 : 0 % + ! % 9 6 . - + & 3 #% # 9 + . + #% #* %;#+ " . , # 9 " + 8 # 9 : 6 # 9 : 8 #* % ;#+ # 1& # : : 8 figure 17 antenna fault en/lzt 720 0011 r1a 2001-07-03 41 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (1) display fault information 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. display the type of fault: go to the operation menu and select monitor . in the rbs monitor setup window, select fault status and click the start monitor button. (2) type of fault? 1. check the start monitor in the omt as described above in stage (1) . which type of fault was found in stage (1) ? answer action auxilliary equipment fault. proceed to stage (3) rx diversity lost. proceed to stage (5) other fault. proceed to stage (7) (3) locate cdu instance 1. select hardware view in the omt. 2. tick the faults check box. 3. look for a red line between a cdu object and an antenna object. 4. when the faulty antenna instance is found, check which cdu it is connected to. this information indicates which auxilliary equipment to replace in stage (4) . (4) replace faulty auxilliary equipment 1. replace or repair the faulty auxilliary equipment. 2. proceed to stage (12) . (5) locate cdu instance 1. select hardware view in the omt. 2. tick the faults check box. 3. look for a red line between a cdu object and an antenna object. 4. when the faulty antenna instance is found, check which cdu it is connected to. this information indicates which rx antenna feeder to replace in stage (6) . (6) replace rx antenna feeders 1. replace the rxa or rxb feeder according to instructions in section rx antenna feeder in chapter rbs field repair . 2. proceed to stage (12) . 42 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (7) rf off in any tru? 1. check all trus in the cabinet. are any of the rf off indicators on? answer comment action yes one or more rf off indicators are on proceed to stage (8) no no rf off indicator is on proceed to stage (10) (8) check trus 1. in the omt, select system view and the object rbs 2000. go to the operation menu and select monitor . 2. in the rbs monitor setup window, select fault status and click the start monitor button. 3. look for the alarm tx antenna vswr limits exceeded in the aotx map. this will point to the tru(s) generating the alarm. note that the indicated tru(s) should match those indicated in stage (7) above. (9) faulty trus found? 1. check the red fault and the green operational indicators on the cdu. could the faulty trus be found by the omt? answer comment action yes one or more faulty trus could be found. proceed to stage (11) no no faulty tru could be found. proceed to stage (10) (10) locate cdu instance 1. select hardware view in the omt. 2. tick the faults check box. 3. look for a red line between a cdu object and an antenna object. 4. when the faulty antenna instance is found, check which cdu it is connected to. this information indicates which tx antenna feeder to replace in stage (11) . (11) replace the tx antenna feeders 1. replace all the tx feeders in the cell according to instructions in section tx antenna feeder in chapter rbs field repair . (12) antenna fault cleared? 1. use the omt to display the type of fault: go to the operation menu and select monitor . en/lzt 720 0011 r1a 2001-07-03 43 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 2. in the rbs monitor setup window, select fault status and click the start monitor button. ? if the fault was "rx diversity lost", it will take at least 1 h 40 min for the fault in the rbs to cease. ? if the fault was "vswr limits exceeded", the tx has to be re-initiated from the bsc. for further information, see section rx and tx antenna feeder in chapter rbs field repair . 3. has the antenna found to be ok in step (2) above? answer comment action yes the antenna fault is cleared. proceed to stage (15) no there is still an antenna fault. proceed to stage (13) (13) replace cdu 1. replace the cdu according to instructions in section cdu in chapter rbs field repair . (14) antenna fault cleared? 1. use the omt to display the type of fault: go to the operation menu and select monitor . 2. in the rbs monitor setup window, select fault status and click the start monitor button. ? if the fault was "rx diversity lost", it will take at least 1 h 40 min for the fault in the rbs to cease. ? if the fault was "vswr limits exceeded", the tx has to be re-initiated from the bsc. for further information, see section rx and tx antenna feeder in chapter rbs field repair . 3. has the antenna found to be ok in step (2) above? answer comment action yes the antenna fault is cleared. proceed to stage (15) no there is still an antenna fault. proceed to stage (18) (15) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? 44 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation answer comment action yes there are no faults in the rbs. proceed to stage (16) no there is still one or more faults in the rbs. proceed to stage (17) (16) test after repair 1. (after replacing a cdu only) make a test call according to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (17) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (18) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.5 battery the battery fault only arises when the external battery back-up system, speci cally bbs 2000, is connected to the rbs. en/lzt 720 0011 r1a 2001-07-03 45 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation " . # * ( % % + # $# , % # 9 " # 9 : 6 . $ # - #+0 : 8 8 figure 18 battery fault, external batteries (1) localise fault on external battery system 1. check that the battery cable is properly connected to the rbs. 2. check the battery cable from the external battery system to the rbs. replace if needed. 3. refer to manufacturer s documentation to perform fault localisation on the external battery system. (2) battery fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the battery fault disappeared? answer comment action yes the battery fault is cleared. proceed to stage (3) no there is still a battery fault. proceed to stage (6) (3) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. 46 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (4) no there is still one or more faults in the rbs. proceed to stage (5) (4) concluding routines 1. proceed to section before leaving the site in chapter concluding routines . (5) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (6) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.6 battery temp sensor note: this section will be included in the next release. 4.7 bdm or bfu the bdm or bfu fault only arises when the external battery back-up system, speci cally bbs 2000, is connected to the rbs. note: the fault text is always bdm or bfu . as there is no bdm in the rbs 2206, the expression bfu fault is used in the procedure below. en/lzt 720 0011 r1a 2001-07-03 47 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 6" . # * ( % % + # $# , # 9 " # 9 : 6 . $ # - #+0 : 8 8 figure 19 bdm or bfu fault (1) localise fault on external battery system 1. check that the battery cable is properly connected to the rbs. 2. check the battery cable from the external battery system to the rbs. replace if needed. 3. refer to manufacturer s documentation to perform fault localisation on the external battery system. (2) bfu fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the bfu fault disappeared? answer comment action yes the bfu fault is cleared. proceed to stage (3) no there is still a bfu fault. proceed to stage (6) (3) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. 48 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (4) no there is still one or more faults in the rbs. proceed to stage (5) (4) concluding routines 1. proceed to section before leaving the site in chapter concluding routines . (5) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (6) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. en/lzt 720 0011 r1a 2001-07-03 49 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.8 cdu ,, + - + ! . $ # #+0 8 8 & 3+ ( ( # , # 9 " + # 9 : 6 # 9 : : 8 figure 20 cdu fault (1) check for possible database fault 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. check for the presence of any of the following faults: ? so cf i1a:17 hw and idb inconsistent ? so cf i2a:36 ru database corrupted ? so cf i2a:46 db parameter fault 3. if any of the faults listed in step 2 above are found, reload the faulty database. see instructions in section idb in chapter rbs field repair . then proceed to stage (2) below. 50 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4. if none of the faults listed in step 2 above are found, proceed to stage (2) below. (2) cdu fault cleared? 1. check the red fault and the green operational indicators on the cdu. is the fault indicator off and the operational indicator on on the cdu? answer comment action yes the cdu fault is cleared. proceed to stage (5) no there is still a cdu fault. proceed to stage (3) note that the status of the cdu can also be checked with the omt. (3) replace cdu 1. replace the faulty cdu. see instructions in section cdu in chapter rbs field repair . (4) cdu fault cleared? 1. check the red fault and the green operational indicators on the cdu. is the fault indicator off and the operational indicator on on the cdu? answer comment action yes the cdu fault is cleared. proceed to stage (5) no there is still a cdu fault. proceed to stage (8) note that the status of the cdu can also be checked with the omt. (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. en/lzt 720 0011 r1a 2001-07-03 51 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (6) test after repair 1. make a test call over the cdu concerned. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.9 cdu bus/iom bus note: this section will be included in the next release. 4.10 cdu cxu rxa cable and cdu cxu rxb cable note: the fault text is always cdu cxu rxa cable and cdu cxu rxb cable . for simplicity reasons, the expression cable fault is used in the procedure below. 52 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation , + + . $ # #+0 8 8 & #% ( , ( # 9 " + ( # 9 8 6 + - ( # 9 : ! # 9 : : 8 : figure 21 cdu cxu rxa cable and cdu cxu rxb cable fault (1) find and correct the faulty cable 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faulty rx cable. 3. check that the cable is correctly connected at both ends. see section cdu to connection field rbs 2206 in chapter cdu connections . en/lzt 720 0011 r1a 2001-07-03 53 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4. check that the cable connectors are correctly inserted into the mating connectors in the cdu and the cxu. 5. if the fault does not disappear, replace the faulty cable. (2) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cdu cxu rxa cable or cdu cxu rxb cable been cleared? answer comment action yes the cable fault is cleared. proceed to stage (7) no there is still a cable fault. proceed to stage (3) (3) replace cdu 1. replace the cdu connected to the suspected cable. see instructions in section cdu in chapter rbs field repair . (4) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cdu cxu rxa cable or cdu cxu rxb cable been cleared? answer comment action yes the cable fault is cleared. proceed to stage (7) no there is still a cable fault. proceed to stage (5) (5) replace cxu 1. replace the cxu connected to the suspected cable. see instructions in section cxu in chapter rbs field repair . (6) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cdu cxu rxa cable or cdu cxu rxb cable been cleared? answer comment action yes the cable fault is cleared. proceed to stage (7) no there is still a cable fault. proceed to stage (10) 54 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (7) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (8) no there is still one or more faults in the rbs. proceed to stage (9) note that the status of the rbs can also be checked with the omt. (8) test after repair 1. make a test call over the cdu concerned. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (9) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (10) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.11 cdu rx in cable note: the fault text is always cdu rx in cable . for simplicity reasons, the expression cable fault is used in the procedure below. en/lzt 720 0011 r1a 2001-07-03 55 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation " - + ! . $ # #+0 8 8 & #% ( " + ( # 9 : 6 # 9 : : 8 + , ( # 9 figure 22 cdu rx in cable fault (1) find and correct the faulty cable 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. look for "fault status cdu rx in #1". for example, if cdu rx in cable 2 is faulty, it means that the faulty cable is located on cdu 2. 3. check that the correct cable is connected to the cdu. see section cdu antenna connection field rbs 2206 in chapter cdu connections . 4. check that the cable connector is correctly inserted into the connector on the cdu. 5. if the fault does not disappear, replace the faulty cable. 56 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (2) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cdu rx in cable disappeared? answer comment action yes the cable fault is cleared. proceed to stage (5) no there is still a cable fault. proceed to stage (3) (3) replace cdu 1. replace the cdu connected to the suspected cable. see instructions in section cdu in chapter rbs field repair . (4) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cdu rx in cable disappeared? answer comment action yes the cable fault is cleared. proceed to stage (5) no there is still a cable fault. proceed to stage (8) (5) rbs fault indicator off? 1. check that there are no remaining faults in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) test after repair 1. make a test call over the cdu concerned. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. en/lzt 720 0011 r1a 2001-07-03 57 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.12 cxu note: the cxu is currently not supervised by rbs sw. 4.13 cxu dc cable note: the fault text is always cxu dc in cable . for simplicity reasons, the expression cable fault is used in the procedure below. "" - + ! . $ # #+0 8 8 & #% ( " + ( # 9 : 6 # 9 : : 8 + , ( # 9 figure 23 cxu dc cable fault 58 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (1) find and correct the faulty cable 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faulty cxu dc cable. 3. check that the cable is correctly connected at both ends. see section backplane cables in chapter cable connections . 4. check that the cable connector as well as the corresponding connector in the cxu are not burned or mechanically damaged. 5. check that the cable connector is correctly inserted into the mating connector in the cxu. 6. if the fault does not disappear, replace the faulty cable. (2) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cxu dc cable disappeared? answer comment action yes the cable fault is cleared. proceed to stage (5) no there is still a cable fault. proceed to stage (3) (3) replace cxu 1. replace the cxu connected to the suspected cable. see instructions in section cxu in chapter rbs field repair . (4) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cxu dc cable disappeared? answer comment action yes the cable fault is cleared. proceed to stage (5) no there is still a cable fault. proceed to stage (8) (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? en/lzt 720 0011 r1a 2001-07-03 59 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) test after repair 1. make test calls over all trus. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.14 cxu dtru rxa cable and cxu dtru rxb cable note: the fault text is always cxu dtru rxa cable and cxu dtru rxb cable . for simplicity reasons, the expression cable fault is used in the procedure below. 60 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation ", + + . $ # #+0 8 8 & #% ( , ( # 9 " + ( # 9 8 6 + - ( # 9 : ! # 9 : : 8 : figure 24 cxu dtru rxa cable and cxu dtru rxb cable fault (1) find and correct the faulty cable 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faulty rx cable. 3. check that the cable is correctly connected in both ends. see section cdu to connection field rbs 2206 in chapter cdu connections . en/lzt 720 0011 r1a 2001-07-03 61 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4. check that the cable connectors are correctly inserted into the mating connectors in the dtru and the cxu. 5. if the fault does not disappear, replace the faulty cable. (2) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cxu dtru rxa cable or cxu dtru rxb cable been cleared? answer comment action yes the cable fault is cleared. proceed to stage (7) no there is still a cable fault. proceed to stage (3) (3) replace tru 1. replace the tru (dtru) connected to the suspected cable. see instructions in section tru in chapter rbs field repair . (4) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cxu dtru rxa cable or cxu dtru rxb cable been cleared? answer comment action yes the cable fault is cleared. proceed to stage (7) no there is still a cable fault. proceed to stage (5) (5) replace cxu 1. replace the cxu connected to the suspected cable. see instructions in section cxu in chapter rbs field repair . (6) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault cxu dtru rxa cable or cxu dtru rxb cable been cleared? answer comment action yes the cable fault is cleared. proceed to stage (7) no there is still a cable fault. proceed to stage (10) 62 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (7) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (8) no there is still one or more faults in the rbs. proceed to stage (9) note that the status of the rbs can also be checked with the omt. (8) test after repair 1. make a test call over the cdu concerned. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (9) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (10) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. en/lzt 720 0011 r1a 2001-07-03 63 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.15 dxu ," + ! + . $ # #+0 8 8 & 3+ () (# # , # 9 " & 3&) &1<(* : - # 9 : : 8 + 6 # 9 figure 25 dxu fault (1) check for possible esb distribution failure 1. is tg synchronisation used to connect the rbs 2206 to another rbs via an esb cable? if there is no such connection, proceed directly to stage (2) below. otherwise, continue below. 2. use the omt to check for the presence of the following fault: ? so cf i2a:44 esb distribution failure 3. if the fault indicated in step 2 above is found, do the following: ? check all connectors and cables in the connection between esb connectors on the dxus in the two cabinets. 64 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation ? if the external esb cable is suspected to be faulty, replace the cable. see instructions in section esb cable in chapter rbs field repair . (2) dxu fault cleared? 1. check the red fault and the green operational indicators on the dxu. is the fault indicator off and the operational indicator on on the dxu? answer comment action yes the dxu fault is cleared. proceed to stage (6) no there is still a dxu fault. proceed to stage (3) note that the status of the dxu can also be checked with the omt. (3) check the eacu and the ovp box note: when a fault is suspected in the dxu, the overvoltage arrestors in the eacu and the ovp functions of the df must be replaced. if the dxu is faulty, due to surges caused by lightning, then the overvoltage arrestors in the eacu and the ovp functions of the df are likely to be faulty. 1. replace the overvoltage arrestors in the eacu functions of the df. 2. if the pcm connection or esb cable is routed via the df, then the overvoltage arrestors in the ovp functions of the df must be replaced. (4) replace dxu 1. replace the faulty dxu according to instructions in section dxu in chapter rbs field repair . (5) dxu fault cleared? 1. check the red fault and the green operational indicators on the dxu. is the fault indicator off and the operational indicator on on the dxu? answer comment action yes the dxu fault is cleared. proceed to stage (6) no there is still a dxu fault. proceed to stage (9) note that the status of the dxu can also be checked with the omt. en/lzt 720 0011 r1a 2001-07-03 65 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (6) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (7) no there is still one or more faults in the rbs. proceed to stage (8) note that the status of the rbs can also be checked with the omt. (7) test after repair 1. make a test call over all trus. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (8) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (9) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.16 environment note: this section will be included in the next release. 4.17 eom bus note: this section will be included in the next release. 4.18 epc bus/power communication loop the epc bus is a bre optic loop used for control and supervision of the power system. when the loop is opened, the power system switches to stand alone mode and the fault epc bus/power communication loop is set in the ru map. possible faults are a faulty ru or a faulty bre optic cable. the indicator epc bus fault will be lit on the dxu and on those rus that have lost communication with the epc function of the dxu. 66 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation note: the fault text is always epc bus/power communication loop . for simplicity reasons, the expression epc bus fault is used in the procedure below. "6 - + ! . $ # #+0 8 8 & #% (= " + ) (# # 9 : 6 # 9 : : 8 + , ) (# # 9 figure 26 epc bus/power communication loop fault (1) find and correct the faulty cable/ru 1. locate the fault, by using bypassing of the suspected faulty units in order to get a closed loop. when the loop is closed, the epc bus fault indicators on all rus within the loop will be extinguished. bypassing means that, for example, the opto bus cable from td output on psu 1 goes directly to rd input on psu 3. en/lzt 720 0011 r1a 2001-07-03 67 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation "- , " , #% $ ' + ) (# # & # figure 27 example of a fault situation in the power communication loop 2. repeat the bypass until the faulty ru or cable is identi ed. 3. ? if found to be faulty, replace the epc bus cable. ? if found to be faulty, replace any faulty ru in the rbs cabinet according to instructions in section psu , fcu or dxu in chapter rbs field repair . ? if found to be faulty, replace the bfu in the external battery system. see manufacturer s documentation. note: the opto bus cables must have a bending radius of at least 35 mm. (2) epc bus fault cleared? 1. check the yellow indicator epc bus fault on each ru connected to the epc bus. is the indicator epc bus fault off on each ru connected to the epc bus? answer comment action yes the epc bus fault is cleared. proceed to stage (5) no there is still an epc bus fault. proceed to stage (3) note that the status of the epc bus can also be checked with the omt. 68 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (3) replace dxu 1. replace the faulty dxu according to instructions in section dxu in chapter rbs field repair . (4) epc bus fault cleared? 1. check the yellow indicator epc bus fault on all rus connected to the epc bus. is the indicator epc bus fault off on all rus connected to the epc bus? answer comment action yes the epc bus fault is cleared. proceed to stage (5) no there is still an epc bus fault. proceed to stage (8) note that the status of the epc bus can also be checked with the omt. (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) test after repair 1. (only if the dxu has been replaced ) make test calls over all trus. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. en/lzt 720 0011 r1a 2001-07-03 69 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.19 external alarms note: this section will be included in the next release. 4.20 fan "", - # $# ! . $ # #+0 8 8 # 9 : 6 # 9 : 8 + , # 9 . + & #% : " + 1& figure 28 fan fault (1) localise and replace the faulty fan 1. check the fcu to nd which fan is indicated as faulty 2. replace the faulty fan. see instructions in section fan in chapter rbs field repair . (2) fan fault cleared? 1. check the red fan fault indicators on the fcu. are the fan fault indicators off on the fcu? 70 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation answer comment action yes the fan fault is cleared. proceed to stage (5) no the same fan is indicated as faulty. proceed to stage (3) other fan another fan is indicated as faulty. go back to stage (1) note that the status of the fans can also be checked with the omt. (3) replace fcu 1. replace the fcu according to instructions in section fcu in chapter rbs field repair . (4) fan fault cleared? 1. check the red fan fault indicators on the fcu. are the fan fault indicators off on the fcu? answer comment action yes the fan fault is cleared. proceed to stage (5) no there is still a fan fault. proceed to stage (8) note that the status of the fans can also be checked with the omt. (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) concluding routines 1. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . en/lzt 720 0011 r1a 2001-07-03 71 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.21 fcu "" - # $# ! . $ # #+0 8 8 # 9 : 6 # 9 : 8 + , # 9 & 3 ( & : " + figure 29 fcu fault (1) check all cables to the fcu 1. check that all cables to the fcu are correctly connected and free from damages. 2. replace any faulty cable to the fcu. (2) fcu fault cleared? 1. check the red fault indicators on the fcu. are the fault indicators off on the fcu? 72 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation answer comment action yes the fcu fault is cleared. proceed to stage (5) no there is still an fcu fault. proceed to stage (3) note that the status of the fans can also be checked with the omt. (3) replace fcu 1. replace the fcu according to instructions in section fcu in chapter rbs field repair . (4) fan fault cleared? 1. check the red fan fault indicators on the fcu. are the fan fault indicators off on the fcu? answer comment action yes the fcu fault is cleared. proceed to stage (5) no there is still an fcu fault. proceed to stage (8) note that the status of the fans can also be checked with the omt. (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) concluding routines 1. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . en/lzt 720 0011 r1a 2001-07-03 73 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.22 flash card ,6 - + ! . $ # #+0 8 8 + & , & # 9 " + & # 9 : 6 # 9 : : 8 + figure 30 flash card fault (1) replace ash card 1. replace the ash card with a ash card containing the correct idb. see instructions in section flash card in chapter rbs field repair . (2) flash card fault cleared? 1. check with the omt if the flash card fault is cleared. is the fault cleared? 74 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation answer comment action yes the flash card fault is cleared.. proceed to stage (5) no there is still a flash card fault. proceed to stage (3) (3) replace dxu replace the dxu. see instructions in section dxu in chapter rbs field repair . (4) flash card fault cleared? 1. check with the omt if the flash card fault is cleared. is the fault cleared? answer comment action yes the flash card fault is cleared. proceed to stage (5) no there is still a flash card fault. proceed to stage (8) (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) test after repair 1. make a test calls over all trus. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . en/lzt 720 0011 r1a 2001-07-03 75 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.23 psu ,- + - + ! . $ # #+0 8 8 & 3+ ( ( # , # 9 " + # 9 : 6 # 9 : : 8 figure 31 psu fault (1) check for possible database fault 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. check for the presence of any of the following faults: ? so cf i2a:36 ru data base corrupted ? so cf i2a:46 db parameter fault 3. if any of the faults listed in step 2 above are found, reload the faulty database. see instructions in section idb in chapter rbs field repair . 76 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (2) psu fault cleared? 1. check the red fault and the green operational indicators on the psu. is the fault indicator off and the operational indicator on on the psu? answer comment action yes the psu fault is cleared. proceed to stage (5) no there is still a psu fault. proceed to stage (3) note that the status of the psu can also be checked with the omt. (3) replace psu 1. replace the faulty psu. see instructions in section psu in chapter rbs field repair . (4) psu fault cleared? 1. check the red fault and the green operational indicators on the psu. is the fault indicator off and the operational indicator on on the psu? answer comment action yes the psu fault is cleared. proceed to stage (5) no there is still a psu fault. proceed to stage (8) note that the status of the psu can also be checked with the omt. (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) test after repair 1. proceed to section before leaving the site in chapter concluding routines . en/lzt 720 0011 r1a 2001-07-03 77 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.24 psu dc cable note: the fault text is always psu dc cable . for simplicity reasons, the expression cable fault is used in the procedure below. " - # $# ! . $ # #+0 8 8 & #% ( " + ( # 9 : 6 # 9 : : 8 + , ( # 9 figure 32 psu dc cable fault 78 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (1) find and correct the faulty cable 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faulty psu dc cable. 3. check that the cable is correctly connected at both ends. see section power cables in chapter cable connections . 4. check that the cable connector as well as the corresponding connector in the psu are not burned or mechanically damaged. 5. check that the cable connector is correctly inserted into the connector in the psu. 6. if the fault does not disappear, replace the faulty cable. (2) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault psu dc cable disappeared? answer comment action yes the cable fault is cleared. proceed to stage (5) no there is still a cable fault. proceed to stage (3) (3) replace psu 1. replace the psu connected to the suspected cable. see instructions in section psu in chapter rbs field repair . (4) cable fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the fault psu dc cable disappeared? answer comment action yes the cable fault is cleared. proceed to stage (5) no there is still a cable fault. proceed to stage (8) (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? en/lzt 720 0011 r1a 2001-07-03 79 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. (6) concluding routines 1. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 80 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.25 rbs db "" ! + . $ # #+0 8 8 6 # 9 : - # 9 : 8 + " # 9 , + % # : + figure 33 rbs db fault (1) display fault information 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. check for the fault rbs db. (2) reload rbs db 1. reload the faulty database according to instructions in section idb in chapter rbs field repair . en/lzt 720 0011 r1a 2001-07-03 81 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (3) rbs db fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. check for the fault rbs db. is the rbs db fault cleared? answer comment action yes the rbs db fault is cleared. proceed to stage (6) no there is still a rbs db fault. proceed to stage (4) (4) replace dxu 1. replace the faulty dxu according to instructions in section dxu in chapter rbs field repair . (5) rbs db fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. check for the fault rbs db. is the rbs db fault cleared? answer comment action yes the rbs db fault is cleared. proceed to stage (6) no there is still a rbs db fault. proceed to stage (9) (6) rbs fault indicator status? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (7) no there is still one or more faults in the rbs. proceed to stage (8) note that the status of the rbs can also be checked with the omt. (7) test after repair 1. proceed to section before leaving the site in chapter test after repair . 82 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (8) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (9) contact the supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.26 tma cm ""- + - # $# ! . $ # #+0 8 8 , # 9 " + # 9 : 6 # 9 : : 8 & 3 figure 34 tma cm fault (1) check tma cm 1. check that the tma cm is correctly inserted and fastened into the sub-rack in the correct position. en/lzt 720 0011 r1a 2001-07-03 83 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 2. check that the tma power connector is correctly connected to the tma cm. (2) tma cm fault cleared? 1. check the red fault and the green operational indicators on the tma cm. is the fault indicator off and the operational indicator on on the tma cm? answer comment action yes the tma cm fault is cleared. proceed to stage (5) no there is still a tma cm fault. proceed to stage (3) note that the status of the tma cm can also be checked with the omt. (3) replace tma cm 1. replace the faulty tma cm. see instructions in section tma cm in chapter rbs field repair . (4) tma cm fault cleared? 1. check the red fault and the green operational indicators on the tma cm. is the fault indicator off and the operational indicator on on the tma cm? answer comment action yes the tma cm fault is cleared. proceed to stage (5) no there is still a tma cm fault. proceed to stage (8) note that the status of the tma cm can also be checked with the omt. (5) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (6) no there is still one or more faults in the rbs. proceed to stage (7) note that the status of the rbs can also be checked with the omt. 84 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (6) test after repair 1. make test calls over all trus. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (7) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (8) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 4.27 tma cm cable note: this section will be included in the next release. 4.28 tru, dtru or atru note: the fault text is always tru, dtru or atru . for simplicity reasons, the expression tru is used in the procedure below. en/lzt 720 0011 r1a 2001-07-03 85 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation , + + . $ # #+0 8 8 & 3+ ( # , & 3 #% ( " # 9 + 6 # 9 8 - + ( 3+ ! # 9 : # 9 : : 8 : figure 35 tru, dtru or atru fault (1) check for possible database fault 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. check for the presence of any of the following faults: ? so trxc i1a:14 ru database corrupted 86 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation ? so trxc i2a:26 db parameter fault 3. if any of the faults listed in step 2 above is found, reload the faulty database. see instructions in section idb in chapter rbs field repair . 4. proceed to stage (2) below.. (2) check for faulty tx cables 1. replace one or both cdu-tru tx cables according to instructions in section cdu-tru tx cables in chapter rbs field repair . (3) tru fault cleared? 1. check the red fault and the green operational indicators on the tru. is the fault indicator off and the operational indicator on on the tru? answer comment action yes the tru fault is cleared. proceed to stage (8) no there is still a tru fault. proceed to stage (4) note that the status of the tru can also be checked with the omt. (4) replace tru 1. replace the faulty tru according to instructions in section tru in chapter rbs field repair . (5) tru fault cleared? 1. check the red fault and the green operational indicators on the tru. is the fault indicator off and the operational indicator on on the tru? answer comment action yes the tru fault is cleared. proceed to stage (8) no there is still a tru fault. proceed to stage (6) note that the status of the tru can also be checked with the omt. (6) replace tru backplane the fault is probably located in the backplane. 1. replace the tru backplane according to section tru backplane in chapter rbs field repair . en/lzt 720 0011 r1a 2001-07-03 87 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (7) tru fault cleared? 1. check the red fault and the green operational indicators on the tru. is the fault indicator off and the operational indicator on on the tru? answer comment action yes the tru fault is cleared. proceed to stage (8) no there is still a tru fault. proceed to stage (11) note that the status of the tru can also be checked with the omt. (8) rbs fault indicator status? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (9) no there is still one or more faults in the rbs. proceed to stage (10) note that the status of the rbs can also be checked with the omt. (9) test after repair 1. make a test call: ? if a tru was replaced, make a test call over that speci c tru according to section test call in chapter test after repair . ? if the tru backplane was replaced, make test calls over all trus according to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (10) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (11) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. 88 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4.29 y link ", + . $ # #+0 8 8 - : 3 # 9 : ! # 9 : 8 + : 3 # 9 , : 3 # 9 " + & #% ( 6 + ( 3+ 8 : : figure 36 y link fault (1) find and correct the faulty cable 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faulty y link cable. 3. check that the cable is correctly connected at each end. see section backplane cables in chapter cable connections . en/lzt 720 0011 r1a 2001-07-03 89 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation 4. check that the cable connectors are correctly inserted into the connectors in the dxu and the tru backplane. 5. if the fault does not disappear, replace the faulty cable. (2) y link fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the y link fault been cleared? answer comment action yes the y link fault is cleared. proceed to stage (7) no there is still a y link fault. proceed to stage (3) note that the status of the y link can also be checked with the omt. (3) replace dxu 1. replace the dxu according to instructions in section dxu in chapter rbs field repair . (4) y link fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the y link fault been cleared? answer comment action yes the y link fault is cleared. proceed to stage (7) no there is still a y link fault. proceed to stage (5) note that the status of the y link can also be checked with the omt. (5) replace tru backplane 1. replace the tru backplane. see instructions in section tru backplane in chapter rbs field repair . (6) y link fault cleared? 1. use the monitor display faulty rus in the omt to list all rus that are faulty. has the y link fault been cleared? answer comment action yes the y link fault is cleared. proceed to stage (7) no there is still a y link fault. proceed to stage (10) note that the status of the y link can also be checked with the omt. 90 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation (7) rbs fault indicator off? 1. check that there are no faults remaining in the rbs. the yellow rbs fault indicator is located on the rbs status panel as well as on the dxu. is the rbs fault indicator off? answer comment action yes there are no faults in the rbs. proceed to stage (8) no there is still one or more faults in the rbs. proceed to stage (9) note that the status of the rbs can also be checked with the omt. (8) test after repair 1. make test calls over all dtrus. proceed to section test call in chapter test after repair . 2. proceed to section before leaving the site in chapter concluding routines . (9) localise remaining faults 1. use the monitor display faulty rus in the omt to list all rus that are faulty. 2. localise the faults that are listed by the omt. see respective ru section in chapter fault localisation . (10) contact supervisor 1. contact the supervisor, or manager, who will take further action, for example, to consult an fsc. en/lzt 720 0011 r1a 2001-07-03 91 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// fault localisation this page is intentionally left blank 92 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5 rbs field repair the instructions in this chapter describe the replacement of rus and how to put the rbs into operation after a fault has been localised in the rbs. 5.1 local/remote mode the local/remote button can change ru mode between local and remote control. a local/remote button is located on the dxu and the dtrus. rus in local mode do not have communication with the bsc via the abis interface and are therefore isolated from the bsc. the local/remote button is used to isolate the unit from the bsc, for example, when exchanging faulty units in the rbs. rus cannot be changed to remote mode until the data base has been downloaded to the dxu. below is a brief description of the two different changes of state and how to stop a change of mode to remote. , figure 37 control panel on dtru 5.1.1 changing ru mode from remote to local ? the local/remote button is pressed. ? the system disables the local/remote button in order to prevent mistakes. ? the local mode indicator starts ashing to indicate that a change of ru mode to local is in progress. ? the operational indicator turns off in order to indicate that the ru has been taken out of operation. ? a fault report message is sent to the bsc via the abis interface. this means that an external condition class 1 alarm will arise in the bsc. ? the communication link on the abis interface is disconnected and the ru mode is changed to local. en/lzt 720 0011 r1a 2001-07-03 93 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair ? the indicators rf off and local mode both turn on. the operational indicator is also turned on, if the ru is free from class 1 faults, in order to indicate that the ru is in local operation. ? the system enables the local/remote button again. 5.1.2 changing ru mode from local to remote ? the local/remote button is pressed. ? the local mode indicator starts ashing to indicate that a change of ru mode to remote is in progress. ? the operational indicator turns off in order to indicate that the ru has been taken out of operation. ? the communication link on the abis interface is established by order from the bsc. the ru is changed to remote mode immediately after the link towards the bsc has been established. ? the indicators rf off and local mode both turn off. ? in order to indicate that the ru is ready to carry traf c, the operational indicator turns on. note that this will only happen if the ru is considered as operational by the bsc. (for example, the unit may be blocked from the bsc.) 5.1.3 stopping a change of ru mode from local to remote if the local/remote button is pushed while the local mode indicator is ashing, the change of ru mode to remote is interrupted. note: this function is only valid during a change of ru mode from local to remote. ? the local/remote button is pressed. ? the attempt to enable a connection with the bsc will stop. ? the ru will then remain in local mode with the communication link disconnected and the indicators rf off and local mode both remain on. 94 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.2 accu the instructions in this section describe the replacement of the entire accu. danger high voltage is used in the operation of this equipment. both direct contact with the mains power and indirect contact via damp items or moisture can be fatal. 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 5. switch off the mains power in the accu. 6. switch off the mains supply to the rbs cabinet. 7. disconnect the cables from the left connection plate. 8. remove the left connection plate. 9. (if no bias injectors are mounted) remove the antenna feeder cables to the left. 10. disconnect the dc cable connected to the bias injector (if mounted). 11. remove the two bias injectors to the left (if mounted). en/lzt 720 0011 r1a 2001-07-03 95 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair ,- > + figure 38 cables, connection plate and accu 12. remove the accu cover plate. 13. disconnect the ac mains cables from the top of the ac mains switch. 96 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair -6 ( figure 39 accu 14. remove the accu. 15. disconnect the accu cables connected to the psus. 16. connect the new accus cables to the psus. 17. mount the accu. 18. reconnect the ac mains cables to the top of the ac mains switch. 19. reattach the accu cover plate. 20. remount the bias injectors (if mounted). 21. reconnect the dc cable connected to the bias injector (if mounted). 22. (if no bias injectors are mounted) reconnect the antenna feeder cables. 23. reattach the left connection plate and reconnect the cables. 24. switch on the mains supply to the rbs cabinet. 25. switch on the mains power in the accu. 26. (if supplied) connect the external battery cabinet to the rbs cabinet. en/lzt 720 0011 r1a 2001-07-03 97 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 27. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off the dxu is in remote mode. note: unless under contractual warranty, after replacement, the accu shall be repaired locally at the rbs site or in a local repair shop. if the accu is irreparable, it shall be disposed of locally by the customer. do not return the accu to ericsson for replacement, repair or disposal. 5.3 antenna feeder " ?# + ?# + > figure 40 antenna feeder note: care must be taken when disconnecting and connecting the antenna feeder cable at the top of the bias injector to avoid damaging the bias injector s dc connector. note: when mounting the antenna feeder cable, a tightening torque, as speci ed by the feeder manufacturer, must be used. exceeding the maximum torque may damage the feeder connector, and thus breaching the antenna feeder cable guarantee. 98 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dtru(s). the local mode indicator will start ashing. 3. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru(s) is in local mode. 4. (without bias injector) disconnect the antenna feeder cable from the cdu. (with bias injector) disconnect the antenna feeder cable from the bias injector. 5. disconnect the antenna feeder cable from the antenna. 6. connect the new antenna feeder cable to the antenna. 7. (without bias injector) connect the new antenna feeder cable to the cdu. (with bias injector) connect the new antenna feeder cable to the bias injector. 8. press the local/remote button on the dtru(s). the local mode indicator will start ashing and when it turns off, the dtru(s) is in remote mode. 5.4 bias injector 6 figure 41 bias injector note: care must be taken when disconnecting and connecting the antenna feeder cable at the top of the bias injector to avoid damaging the bias injector s dc connector. note: when mounting the antenna feeder cable, a tightening torque, as speci ed by the feeder manufacturer, must be used. exceeding the maximum torque may damage the en/lzt 720 0011 r1a 2001-07-03 99 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair feeder connector, and thus breaching the antenna feeder cable guarantee. 1. inform the omc operator that a bias injector will be replaced. 2. press the local/remote button on the dtrus that are connected to the faulty bias injector. the local mode indicator will start ashing. 3. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtrus are in local mode. 4. disconnect the dc cable connected to the bias injector. 5. disconnect the antenna feeder cable connected to the bias injector. 6. replace the faulty bias injector. 7. reconnect the antenna feeder cable to the new bias injector. 8. reconnect the dc cable to the bias injector. 9. press the local/remote button on the dtrus. the local mode indicator will start ashing and when it turns off the dtrus are in remote mode. 5.5 cdu note: cdus are marked on the front with a label showing the frequency. make sure that the appropriate cdu is available. 100 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair ,@, !- / /a # 1+ (# (# , , # 1+ , @ @, ,@ , , (# #, # #, # , figure 42 cdu-g and cdu-f caution radio frequency (rf) radiation from antenna systems can endanger your health. note: care must be taken when disconnecting and connecting the antenna feeder cable at the top of the bias injector to avoid damaging the bias injector s dc connector. note: when mounting the antenna feeder cable, a tightening torque, as speci ed by the feeder manufacturer, must be used. exceeding the maximum torque may damage the feeder connector, and thus breaching the antenna feeder cable guarantee. 1. inform the omc operator that the cdu will be replaced. 2. press the local/remote button on the dtrus that are connected to the faulty cdu. the local mode indicator will start ashing. note: in certain con gurations, three cdu-fs are connected. in these cases, all dtrus connected to the cdu-fs connected to the faulty cdu-f must be set in local mode. 3. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru(s) is in local mode. en/lzt 720 0011 r1a 2001-07-03 101 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 4. switch off the circuit breaker cdu 1, cdu 2 or cdu 3. note: to prevent damage to trus and exposure to rf radiation, be sure that the indicators rf off and local mode on the trus, that are connected to the faulty cdu, all have a xed yellow light before taking any further actions. 5. (with bias injectors) remove the bias injectors connected to the faulty cdu. see section 5.4 bias injector on page 99 . (without bias injectors) remove the antenna feeder cables. 6. disconnect all cables connected to the faulty cdu. 7. if the cdu is equipped with a cnu, move the cnu to the new cdu. see instructions in section 5.9 cnu on page 106 . 8. replace the cdu. 9. (with bias injectors) reattach the bias injectors. (without bias injectors) reconnect the antenna feeder cables. 10. reconnect all cables. 11. switch on the circuit breaker cdu 1, cdu 2 or cdu 3. 12. press dxu reset on the dxu. the ru information from the new cdu will then be loaded into the rbs data base. 13. press the local/remote buttons on both dtrus that are connected to the new cdu. the local mode indicator will start ashing and when it turns off the dtrus are in remote mode. note: if baseband hopping is used, the hopping sequence can only be re-initiated by the bsc/msc. after placing a dtru in remote mode, contact the bsc/msc and request they take the required action. note: after replacement, the cdu must be returned to ericsson for repair. maintenance personnel must attach a repair delivery note, lzf 084 64 (blue tag), to the cdu. the repair delivery note must include a clear description of the fault found. see the chapter concluding routines for instructions on completing a repair deliver note. 5.6 cdu bus 1. press the local/remote button on the dtru(s). the local mode indicator will start ashing. 2. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru(s) is in local mode. 3. disconnect the cdu bus cable attached to the cdu. 4. connect the new cdu bus cable to the cdu. 5. remove the idm. 6. remove the dtru. 102 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 7. disconnect the cdu bus cable attached to the tru backplane. 8. connect the new cdu bus cable to the tru backplane. 9. mount the dtru and the idm. 10. press the local/remote button on the dtru(s). the local mode indicator will start ashing and when it turns off, the dtru(s) is in remote mode. en/lzt 720 0011 r1a 2001-07-03 103 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.7 cdu-cxu and the tru-cxu rx cables " /a / , , , , , , , , , , , , figure 43 cdu-cxu and tru-cxu rx cables caution radio frequency (rf) radiation from antenna systems can endanger your health. 1. press the local/remote button on the dtru that is connected to the faulty cable. the local mode indicator will start ashing. 2. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru is in local mode. note: to prevent damage to dtrus and exposure to rf radiation, ensure that the local mode indicator on the dtru that is 104 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair connected to the faulty cdu-tru rx cable has a xed yellow light before taking any further action. 3. replace both the rx1 and rx2 cables. 4. press the tru reset button on the dtru. 5. press the local/remote button on the dtru that is connected to the new cable(s). the local mode indicator will start ashing and when it turns off the dtru is in remote mode. note: unless under contractual warranty, after replacement, the cables shall be disposed of locally. do not return the cables to ericsson for replacement, repair or disposal. 5.8 cdu-tru tx cables # % /a /a / , , , " # #, b, b, , , figure 44 cdu-tru tx cables caution radio frequency (rf) radiation from antenna systems can endanger your health. 1. press the local/remote button on the dtru that is connected to the faulty cable. the local mode indicator will start ashing. 2. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru is in local mode. en/lzt 720 0011 r1a 2001-07-03 105 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair note: to prevent damage to dtrus and exposure to rf radiation, ensure that the local mode indicator on the dtru that is connected to the faulty cdu-tru tx cable has a xed yellow light before taking any further action. 3. replace the cable. 4. press the tru reset button on the dtru. 5. press the local/remote button on the dtru that is connected to the new cable(s). the local mode indicator will start ashing and when it turns off the dtru is in remote mode. note: unless under contractual warranty, after replacement, the cables shall be disposed of locally. do not return the cables to ericsson for replacement, repair or disposal. 5.9 cnu 6 / 8 figure 45 cnu 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dtru(s). the local mode indicator will start ashing. 3. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru(s) is in local mode. 4. switch off circuit breaker cdu 1, cdu 2 or cdu 3 on the idm. 5. disconnect the cable from the cnu. 106 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 6. remove the cnu by unscrewing the eight screws. see gure above. 7. attach the new cnu to the cdu-f and tighten the eight screws. 8. connect the cable from the cnu to the cdu. 9. switch on circuit breaker cdu 1, cdu 2 or cdu 3 on the idm. 10. press the local/remote button on the dtru(s). the local mode indicator will start ashing and when it turns off, the dtru(s) is in remote mode. 5.10 cxu 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. switch off circuit breaker cxu1 2 on the idm. 5. remove all cables connected to the cxu. 6. replace the cxu and reconnect the disconnected cables. 7. switch on circuit breaker cxu1 2 on the idm. 8. press the local/remote button on the dxu. the local mode indicator will start ashing. 9. when the local mode indicator is turned off, the dxu is in remote mode. 10. check that the rbs fault indicator (dxu) is off. this means that there are no active faults in the rbs. en/lzt 720 0011 r1a 2001-07-03 107 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.11 dccu the instructions in this section describe the replacement of the entire dccu. danger high voltage is used in the operation of this equipment. both direct contact with the mains power and indirect contact via damp items or moisture can be fatal. !6 figure 46 dccu 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 5. switch off the main power in the dccu. 108 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 6. switch off the mains supply to the rbs cabinet. 7. disconnect the cables from the left connection plate. 8. remove the connection plate. 9. (if no bias injectors are mounted) remove the antenna feeder cables to the left. 10. disconnect the dc cable connected to the bias injector (if mounted). 11. remove the two bias injectors to the left (if mounted). 12. remove the dccu cover plate. 13. disconnect the dc supply cables from the top of the dc main switch. 14. remove the dccu. 15. disconnect the dccu cables connected to the psus. 16. connect the new dccus cables to the psus. 17. mount the new dccu. 18. reconnect the dc supply cables to the top of the dc main switch. 19. reattach the dccu cover plate. 20. remount the bias injectors (if mounted). 21. reconnect the dc cable connected to the bias injector (if mounted). 22. (if no bias injectors are mounted) reconnect the antenna feeder cables. 23. reattach the connection plate and reconnect the cables. 24. switch on the mains supply to the rbs cabinet. 25. switch on the main power in the dccu. 26. (if supplied) connect the external battery cabinet to the rbs cabinet. 27. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off the dxu is in remote mode. 5.12 dc filter note: these instructions are valid only for cabinets equipped with external batteries. en/lzt 720 0011 r1a 2001-07-03 109 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair *c;#8 / figure 47 dc lter 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 5. switch off the main power in the accu or dccu. 6. remove the bias injectors. 7. remove the dccu cover. 8. disconnect the dc cables connected to the dc lter. 9. remove the connection plate to the right. 10. remove the dc lter. 11. remove the idm front panel. 12. disconnect the dc cables connected to the idm. 13. connect the dc cables from the dc lter to the idm and reattach the idm front panel. 14. mount the replacement dc lter. 15. reconnect the dc cables to the dc lter, mount the dccu cover, the connection plate to the right and the bias injectors. 110 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 16. switch on the main power in the accu or dccu. 17. (if supplied) connect the external battery cabinet to the rbs cabinet. 18. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off the dxu is in remote mode. note: unless under contractual warranty, after replacement, the dc lter shall be disposed of locally. do not return the dc lter to ericsson for replacement, repair or disposal. 5.13 dtru see section 5.26 tru on page 123 . 5.14 dxu !,! !" #" $ %& !" ' ! # $ ( $ # )*' )'+ , ! , ) - figure 48 dxu-21 1. inform the omc operator that the rbs will be removed from service temporarily. en/lzt 720 0011 r1a 2001-07-03 111 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. switch off circuit breaker dxu/sys.volt.sens on the idm. 5. remove all cables connected to the dxu. 6. remove the flash card from dxu and place it in the new dxu before sending the dxu to the repair centre. note: if the flash card is faulty, reload the idb. see section 5.19 flash card on page 117 . 7. replace the dxu and reconnect the disconnected cables. 8. switch on circuit breaker dxu/sys.volt.sens on the idm. 9. press the dxu reset button on the dxu. this will distribute the idb to the rus. 10. wait until the operational indicator on the new dxu has a xed green light. 11. press the local/remote button on the new dxu. the local/remote button will start ashing and when it turns off, the dxu is in remote mode. 12. make a request to the omc operator to check that all mos are operational. note: after replacement, the dxu must be returned to ericsson for repair. maintenance personnel must attach a repair delivery note, lzf 084 64 (blue tag), to the dxu. the repair delivery note must include a clear description of the fault found. see chapter concluding routines for instructions on completing a repair delivery note. 5.15 dxu backplane note: when changing the dxu backplane, see chapter cable connections . note the position of rus within the original sub-rack, so that they can be replaced into the correct position without changing the idb. 112 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair , figure 49 dxu backplane 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 5. switch off the main power in the accu or dccu. 6. disconnect all the cables to the psus, dxu and tma cm. 7. take out the psus, tma cm and dxu. 8. remove the dxu sub-rack. 9. disconnect all the cables to the dxu backplane. 10. remove the dxu backplane from the dxu sub-rack. 11. mount a new dxu backplane to the dxu sub-rack. 12. connect all the cables to the dxu backplane and insert the dxu sub-rack. 13. remount the psus, tma cm and dxu. 14. connect the cables to the rus. 15. reconnect the cabinet to the external power source (either ac or dc). 16. switch on the main power in the accu or dccu. 17. (if supplied) connect the external battery cabinet to the rbs cabinet. en/lzt 720 0011 r1a 2001-07-03 113 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 18. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. note: unless under contractual warranty, after replacement, the dxu backplane shall be disposed of locally. do not return the dxu backplane to ericsson for replacement, repair or disposal. 5.16 esb cable ,! ) figure 50 esb cable 1. remove the esb cable from the dxu. 2. remove the left connection plate and disconnect the esb cable. 3. connect the new esb cable to the connection plate and remount the connection plate. 4. connect the new esb cable to the dxu. 114 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.17 fans ,!! , " figure 51 fans 1. switch off circuit breaker fan 1, fan 2, fan 3 or fan 4 on the idm. 2. remove the cover plate, on top of the cabinet, protecting the fans. 3. pull out the faulty fan. note: remove fan 1 before replacing fan 2. remove fan 4 before replacing fan 3. 4. disconnect the cable. 5. reconnect the cable to the new fan. 6. mount the new fan. 7. reattach the cover plate. 8. switch on circuit breaker fan 1, fan 2, fan 3 or fan 4 on the idm. en/lzt 720 0011 r1a 2001-07-03 115 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.18 fcu ,-6 figure 52 fcu 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. disconnect the epc bus cable attached to the front of the fcu. 5. remove the screws holding the fcu and pull it out. 6. disconnect the cables. 7. connect the cables to the new fcu and push it into place. 8. tighten the screws holding the fcu. 9. connect the epc bus cable to the front of the fcu. 10. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. 116 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.19 flash card ! ' # $).!" figure 53 flash card position in the dxu 1. remove the dxu. see section 5.14 dxu on page 111 for further information. 2. press the button on top of the dxu. 3. replace the ash card. 4. mount the dxu. see section 5.14 dxu on page 111 for further information. 5. connect the omt and download the original rbs idb into the dxu. there are two alternative databases that can be used: ? use the database that was acquired when reading the rbs data base. ? create a new database. 5.20 idb use the omt to install a new idb. for further information on the use of the omt, see: omt user s manual lzn 302 01 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. connect and establish a link between the omt and the rbs. 5. install the idb into the rbs. en/lzt 720 0011 r1a 2001-07-03 117 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 6. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. 5.21 idm ! $/0 1 ! 2 ! 3 2 2 2 3 3 ! 2 2 3 ! 2 ! ' 2 2 2 ! 2 4 #'3 2 3 3 + 3 $/& 0 & 2 2 2 2 / b ) 5 1 8 a 1 8 8 a figure 54 idm note: care must be taken when replacing the idm to prevent damage to the main dc power cables to the right side and the dc power distribution cables at the back of the idm. 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 5. switch off the main power in the accu or dccu. 6. remove the idm front plate. 7. disconnect all cables. 8. replace the idm. 9. connect all cables and reattach the idm front plate. 118 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 10. switch on the main power in the accu or dccu. 11. (if supplied) connect the external battery cabinet to the rbs cabinet. 12. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. note: unless under contractual warranty, after replacement, the idm shall be disposed of locally. do not return the idm to ericsson for replacement, repair or disposal. 5.22 psu 4. 3'235! 23+367 !" $'! !" !" 8*&5 ! 339 !, !'" 4. ' :'+35 ! $' ! 8*&5 ! 339 !" !" figure 55 psu-ac and psu-dc note: the opto bus cables for the power communication loop must have a bend radius of at least 35 mm. note: if the cabinet, from which the psu is being removed, has external battery back-up, the dc cable will be live when disconnecting it from the psu. 1. disconnect all cables connected to the psu. 2. replace the faulty psu. en/lzt 720 0011 r1a 2001-07-03 119 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 3. connect all cables to the psu. note: after replacement, the psu must be returned to ericsson for repair. maintenance personnel must attach a repair delivery note, lzf 084 64 (blue tag), to the psu. the repair delivery note must include a clear description of the fault found. see chapter concluding routines for instructions on completing a repair delivery note. 5.23 psu dc cable 4. 3'235! 23+367 !" $'! !" !" 8*&5 ! 339 6 !'" 4. ' :'+35 ! $' ! 8*&5 ! 339 !" !" ( figure 56 psu dc cable 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 120 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5. switch off the main power in the accu or dccu. 6. disconnect the dc cable connected to the psu. 7. remove the idm. 8. disconnect the dc cable connected to the back of the idm. 9. connect the new dc cable to the idm. 10. mount the idm. 11. connect the dc cable to the psu. 12. switch on the main power in the accu or dccu. 13. (if supplied) connect the external battery cabinet to the rbs cabinet. 14. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. 5.24 rx antenna feeder see section 5.3 antenna feeder on page 98 . en/lzt 720 0011 r1a 2001-07-03 121 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 5.25 tma cm figure 57 tma cm 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the local mode indicator has a xed yellow light, indicating that the dxu is in local mode. 4. switch off circuit breaker oxu 1 or oxu 2 on the idm. 5. remove the cable connected to the tma cm. 6. replace the tma cm. 7. reconnect the disconnected cable. 8. switch on circuit breaker oxu 1 or oxu 2 on the idm. 9. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. 122 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair note: after replacement, the tma cm must be returned to ericsson for repair. maintenance personnel must attach a repair delivery note, lzf 084 64 (blue tag), to the tma cm. the repair delivery note must include a clear description of the fault found. refer to the chapter concluding routines for instructions on completing a repair delivery note. 5.26 tru note: trus are marked on the front with a label showing frequency. ensure that the appropriate tru is available. !! / 5 b, 5 , , , " # 1+ . . = figure 58 dtru 1. press the local/remote button on the tru. the local mode indicator will start ashing. 2. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru is in local mode. 3. switch off circuit breaker tru 1, tru 2, tru 3, tru 4, tru 5 or tru 6 on the idm. 4. remove all cables connected to the tru. 5. replace the tru. en/lzt 720 0011 r1a 2001-07-03 123 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 6. reconnect the disconnected cables. 7. switch on circuit breaker tru 1, tru 2, tru 3, tru 4, tru 5 or tru 6 on the idm. 8. wait until the operational indicator has a xed green light. if the new tru contains an old software version, the dxu will automatically download the correct version. the software download procedure is indicated by a ashing operational indicator and may take some time (up to 10 minutes). 9. press the local/remote button on the new tru. the local mode indicator will start ashing and when it is turned off, the tru is in remote mode. note: after replacement, the tru must be returned to ericsson for repair. maintenance personnel must attach a repair delivery note, lzf 084 64 (blue tag), to the tru. the repair delivery note must include a clear description of the fault found. see the chapter concluding routines for instructions on completing a repair delivery note. 5.27 tru backplane :/.8d /" :/.8d /- 1 / / / 1 6 , - 6 " , 6 - ! ,< < 6 - ! ,< < 6 - ! ,< < 6 - ! ,< < 6 - ! ,< < 6 - ! ,< < " " " " " , figure 59 tru backplane (note that there is a newer version of the tru backplane) 1. inform the omc operator that the rbs will be removed from service temporarily. 2. press the local/remote button on the dxu. the local mode indicator will start ashing. 3. wait until the indicators rf off and local mode both have a xed yellow light, indicating that the dtru is in local mode. 4. (if supplied) isolate the rbs cabinet from battery power in the external battery cabinet. 5. switch off the main power in the accu or dccu. 6. disconnect all cables connected to the dtrus. 7. remove the dtrus. 124 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair 8. disconnect all cables connected to the tru backplane. 9. replace the tru backplane. 10. connect all the cables to the tru backplane. 11. mount all the dtrus and connect all cables. 12. switch on the main power in the accu or dccu. 13. (if supplied) connect the external battery cabinet to the rbs cabinet. 14. press the local/remote button on the dxu. the local mode indicator will start ashing and when it turns off, the dxu is in remote mode. note: unless under contractual warranty, after replacement, the tru backplane shall be disposed of locally. do not return the tru backplane to ericsson for replacement, repair or disposal. 5.28 tx antenna feeder see section 5.3 antenna feeder on page 98 . en/lzt 720 0011 r1a 2001-07-03 125 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// rbs field repair this page is intentionally left blank 126 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// test after repair 6 test after repair this chapter describes the methods for verifying the rbs. the intention is to verify that the problem has been solved and that the rbs is fully functional. note: all known faults must be cleared before performing the tests. 6.1 preconditions test calls should be performed with a tems using the tems software. 6.2 test call test calls must be made when a cxu, tru or cdu has been replaced to ensure that the replaced units carry traf c. if the technican is required to make a test call on a speci c ru, information is needed on the arfcn(s) for each tru. contact the bsc personnel for information on arfcn(s). the test procedure is divided into two parts, that are done in sequence. the rst test sequence of the downlink connection is monitored by the tems. the second test sequence of the uplink connection is monitored by the omt. note: before starting the test call, the operational indicators on the dxu and trus must be on. set all units to remote mode. monitoring the dedicated channel with a tems 1. connect the tems to the pc serial port. 2. start the tems program in the windows environment. 3. select enable connections in the externals menu and specify the serial port for the tems. 4. contact the bsc personnel to nd out which arfcn and ts that a test call should be performed on. the bsc personnel can use the printout command: rxcdp:mo=rxotg-tg; note: the rxcdp gives, for the tg speci ed, the arfcn and tn (timeslot number on the air interface) that corresponds to the equipment ts. the ts and tn are normally the same, but there are exceptions. therefore always check the tn with rxcdp). 5. choose cell selection in the control menu. 6. choose target frequency and select the arfcn for the tru that is to be tested. mark the frequency in the list. 7. disable the handover button in the cell selection menu. 8. select status information in the monitor menu. 9. choose dedicated channel. en/lzt 720 0011 r1a 2001-07-03 127 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// test after repair 10. make a call from the tems. 11. monitor the dedicated channel in tems and verify the downlink (dl) by checking that the targeted arfcn and tn appear in the monitor. 12. make repeated calls until the desired information appears in the monitor, see the gure below. channel number (arfcn): 11 timeslot number (tn): 2 channel type and bm + acchs tdma offset: channel mode: speech full rate subchannel number: hopping channel: no mobile allocation index offset (maio): hopping sequence number (hsn): dedicated channel 06_0178a figure 60 tems dedicated channel monitor supervising the traf c channel with the omt 1. connect the omt cable between the omt connector on the dxu and the pc serial port. 2. start the omt program in the windows environment. 3. select connect in the connection menu. 4. select the read idb function in the file menu. 5. change view mode to mo view . 6. select the appropriate trxc object. 7. choose operation monitor . 8. in the monitor setup dialogue box, scroll down the list and select the desired tch-ts to monitor. 9. make a call on the tems. 10. while a call is in progress in the correct timeslot, select the start monitor button. 11. check the rx-lev full and rx-lev sub values, see the gure below . 128 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// test after repair 6"! $3 !'3 0# = 5= ,= 5@ ,= 5 / /)@e6 / )#@.14 / ) #(@.14 /.)<#@/ /.)< #(@/ /<@ 6@6@" #+0 < # 5/ , ,= 5 a @ <) . 3 @ 5 1f 8 d + &2 #+ figure 61 example of omt supervision value tch-ts 2 12. repeat the procedure above for additional tn values as well as other trus. 13. compare the rx-lev values. note that the values should be in the same range for all trus. 14. proceed to chapter concluding routines and complete the checklist. en/lzt 720 0011 r1a 2001-07-03 129 (201) ericsson radio systems ab ? all rights reserved ? free datasheet http:// test after repair this page is intentionally left blank 130 (201) en/lzt 720 0011 r1a 2001-07-03 ericsson radio systems ab ? all rights reserved ? free datasheet http:// concluding routines 7 concluding routines the following is a description of the different administrative routines that must be carried out as a result of a maintenance procedure. 7.1 before leaving the site the following checklist is strongly recommended. local procedures and safety regulations must be evaluated and incorporated into this checklist. if the answer to any of the items is no, do not depart from the site until the problem/fault has been cleared or investigated. table 8 recommended checklist, before leaving the site. n/a means not applicable item n/a yes no 1 is the rbs fault indicator off? 2 are the red fault indicators off? 3 are all operational green indicators on? 4 is the rbs in "remote" mode? (yellow "local" indicator on dxu is off) 5 are all other yellow indicators off? 6 are all the warning signs ?ed and located correctly in the cabinet? 7 is the cabinet dry with no water in it? 8 is the inside and outside of the cabinet free from mechanical damage or rust? 9 is the back-up copy of the rbs idb saved on a disk? 10 are all tools accounted for? 11 is the cabinet door locked? 12 is the external air intake free from obstructions? 13 is the defective part packed for shipment, including repair delivery note? 14 are all other necessary paper work completed? 15 are the hazard lights on the antenna operational? 16 do the antennas, towers, and rf cables appear in operational order? 17 is the omc noti?d and alarms ceased? signature: date: 7.2 report of finished work when a maintenance procedure has been completed, a report will be written including a detailed description of actions taken, all observations made in accordance with local routines for work orders, site log-book, etc. en/lzt 720 0011 r1a 2001-07-03 131 (201) ericsson radio systems ab all rights reserved free datasheet http:// concluding routines 7.3 repair delivery note blue tag when a faulty unit is returned, it must be accompanied by a repair delivery note. when the note has been completed it is attached to the faulty unit with a string, before sending it for repair. tape can only be used to attach the note to the sides of the unit. do not tape it to the control panel. the repair delivery note lzf 084 84 can be ordered from the local fsc. a description of how to ll in a repair delivery note follows below. g+ ,g+& 8c 6g # % -g)* & $ !g g #08c g 8c g 8c g# 8c ,g/ "g & 8c g 2 ++ 6g# + -g # !g % g 8c g # ch% e23g ,g + # ,g #++# 8c ,,g/ ,"g 8c ,g ,6g 0 ,!g 8c ,g 0 ,-g 3 = + # "g # h%%%%/ /g g # # + < ,g h%%%%/ /g )).<):81) # 0 .i=)8 66"! 69 !"#$%&"%'&(#")%'*+' #%&%',* -%"$$'& .$/)$'*"*'$#&'& &2 $ %c ( 3 c + 0 & j ,+& 0 & j +& # ( " # # 32& # # + < 6 # % 2 # % ! 5 2 h54g # 2& # #@ f 0 2& # #h+ g f82# # $ h g f+ # # $ h + g # 8c #%# ,/ #%# 2 e+# # ( / ++ - # & 31 23 8c #%# # c h% 23g , + 1( 0 * # , #+ %+ +# 8c , # e + %e + ,- 3 = + (# e$ ;# # 0123.012- 4405555 figure 62 the blue tag the above explanations to the repair delivery note are also given on its reverse side. 7.4 handling of replaced parts and rus replaced parts and rus are divided into three categories: ? customer disposable ? customer repairable 132 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// concluding routines ? depot repairable the de nitions of these categories as well as explanations how to treat the parts is given below. customer disposable customer disposable parts are consumable parts, which have no lower sub-assembly or component that can be used to repair them. these items are identi ed in the appropriate rbs spare parts catalogue as "recommended spare parts for customer stock (not repairable)" or "other available parts". spare parts catalogue examples of these parts are: ? cables and wiring ? connectors ? fuses, circuit breakers, varistors and overvoltage arresters ? fans, compressors and heaters ? printed circuit board assemblies (circuit cards, backplanes, temperature sensors and humidity sensors) ? batteries ? antennas ? transformers ? capacitors ? mechanical hardware (doors, hinges, plates, locks, seals, gaskets, brackets and other parts of the rbs cabinet) unless under contractual warranty, after replacement, these parts shall be disposed of locally. do not return these parts to ericsson for replacement, repair or disposal. customer repairable customer repairable parts are such parts, which have a lower sub-assembly or component that can be used to repair them. these items are identi ed in the appropriate rbs spare parts catalogue as "recommended spare parts for customer stock (not repairable)" or "other available parts". spare parts catalogue examples of these parts are: ? idms unless under contractual warranty, after replacement, these parts shall be repaired locally at the rbs site or in a local repair shop. en/lzt 720 0011 r1a 2001-07-03 133 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// concluding routines depot repairable depot repairable parts are for direct one to one replacement at the rbs site. these items are identi ed in the appropriate rbs spare parts catalogue as "recommended spare parts for customer stock (repairable)". spare parts catalogue examples of these parts are: ? cdus ? dxu ? psus ? trus ? cxu after replacement, these parts must be returned to ericsson for repair. maintenance personnel must attach a repair delivery note, lzf 084 64 (blue tag), to the returned part. the repair delivery note shall include a clear description of the fault found. refer to the section "repair delivery note blue tag " for instructions on completing a repair delivery note. 7.5 transport of a repairable unit the repairable unit must be protected against esd and damage due to transport. therefore the repairable unit must be packed in an esd- insulated plastic bag and transported in a shock-absorbing box. this must be done by re-using the same packing material as the spare unit was delivered in. refer to the appropriate spare parts catalogue to determine which repairable units should be returned for repair. spare parts catalogue 7.6 trouble report on equipment or on this manual a trouble report should be written when system components are not operating as expected or when disturbances occur repeatedly. it should not be written for occasional hardware failures. a trouble report should also be written when a fault is found in this manual. any comments on this manual can be submitted in a similar way. when writing a trouble report, always include as much information as possible. write the trouble report as soon as possible, preferably at the rbs site. the next pages contain an example of a lled-in trouble report and a blank trouble report. the trouble report should be sent to the nearest fsc for resolution and registration in the ericsson trouble report system mhs (modi cation handling system). the fsc should forward the trouble report via the node mho era bts. 134 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// concluding routines 7.6.1 special explanations product number the product number can be found on the label of the unit. for example krc 131 47/01 r-state revision state, found on the label of the unit after the product number. for example r1a site status can be installation test or operation en/lzt 720 0011 r1a 2001-07-03 135 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// concluding routines 7.6.2 example of filled-in trouble report 5 $@ # # ( # # (@ / # @ @ @ #( % + @ #( + @ + %@ #(%@ @ & @ @ * @ #(+ @ "7! figure 63 example of lled-in trouble report 136 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// concluding routines 7.6.3 trouble report, blank ,7! 5 $@ # # ( # # (@ / @ # @ @ 8 @ #( % + @ #( + @ + %@ #(%@ @ @ & 8@ @ *8@ #(+ @ figure 64 trouble report, blank en/lzt 720 0011 r1a 2001-07-03 137 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// concluding routines this page is intentionally left blank 138 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8 optical indicators and switches 8.1 indicator types rbs 2000 optical indicators are either red, green or yellow. the indicators can be on, off or ashing. their general functions are: ? red, fault ? green, operational ? yellow, status 8.1.1 self test of indicators on the rus dxu and tru, there is a self test of indicators performed at startup or restart. all indicators are switched on and remain switched on until the bts software is started. 8.2 units with optical indicators and switches the cdu-f, cdu-g, cxu, dtru, dxu, fcu, idm, psu, tma-cm and rbs status panel units in the cabinet are equipped with indicators. the accu, dccu, dtru, dxu and idm units in the cabinet are equipped with switches. 8.3 accu - 9.4.( .4 . #4.$$94!6 !!'3 figure 65 accu-01 table 9 switches on accu-01 label position function 1 mains power connected mains switch 0 mains power disconnected en/lzt 720 0011 r1a 2001-07-03 139 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8.4 cdu-f "- / # 1+c # 1+c figure 66 cdu-f table 10 optical indicators on cdu-f label colour mode indication fault red off no fault is detected in cdu-f on a fault is detected in cdu-f oper. green off cdu-f not operational on cdu-f operational 140 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8.5 cdu-g /a (# "! # 1+c # 1+c figure 67 cdu-g table 11 optical indicators on cdu-g label colour mode indication fault red off no fault is detected in cdu-g on a fault is detected in cdu-g oper. green off cdu-g not operational on cdu-g operational en/lzt 720 0011 r1a 2001-07-03 141 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8.6 cxu , 1+c # 1 (# figure 68 cxu table 12 optical indicators on cxu label colour mode indication fault red off no fault is detected in cxu on a fault is detected in cxu oper. green off cxu not operational on cxu operational 8.7 dccu #4.$94!6 !!'3 ! figure 69 dccu-01 142 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches table 13 switches on dccu-01 label position function 1 -48 v dc power is connected main switch 0 -48 v dc power is disconnected 8.8 dtru , figure 70 dtru table 14 optical indicators on dtru label colour mode indication fault red off no fault is detected in dtru on a fault is detected in dtru operational green off dtru is not operational on dtru is operational flashing one of the following applies: ? software being downloaded ? con guration activity in progress which may take longer than 10 seconds to complete ? restart by bsc pending rf off yellow off tx enabled on tx not enabled local yellow off dtru in remote mode. dtru controlled by bsc on dtru in local mode. dtru controlled by rbs flashing change of dtru mode (from local mode to remote mode, or from remote mode to local mode) in progress. link between bsc and rbs being established or released en/lzt 720 0011 r1a 2001-07-03 143 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches table 15 switches on dtru label function tru reset when pushed, resets the dtru and all units subordinated to the dtru local/remote when pushed, changes the dtru mode between local and remote 8.9 dxu !,! !" #" $ %& !" ' ! # $ ( $ # )*' )'+ , ! , ) - figure 71 dxu-21 table 16 optical indicators on dxu-21 label colour mode indication fault red off no fault is detected in dxu on a fault is detected in dxu 144 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches operational green off dxu is not operational on dxu is operational flashing one of the following applies: ? software is being received ? con guration activity in progress which may take longer than 10 seconds to complete ? restart by bsc pending local yellow off dxu is in remote mode. dxu is controlled by the bsc on dxu is in local mode. dxu has no established link to the bsc flashing a change of dxu mode (from local mode to remote mode or from remote mode to local mode) is in progress. the link between bsc and rbs is being established or released rbs fault yellow off no faults are detected in the rbs on one or more faults are detected in the rbs ext. alarm yellow off no external alarms are active on one or more external alarms are active epc bus fault yellow off there is no communication fault on the epc bus on a communication fault on the epc bus is detected eom bus fault yellow for future use port a yellow off loss of signal or loss of frame alignment detected on port a on transmission ok on port a port b yellow off loss of signal or loss of frame alignment detected on port b on transmission ok on port b port c yellow off loss of signal or loss of frame alignment detected on port c on transmission ok on port c port d yellow off loss of signal or loss of frame alignment detected on port d trans- mission ok on transmission ok on port d table 17 switches on dxu-21 label function dxu reset when pushed, resets dxu and trus local/remote when pushed, changes dxu mode between local and remote en/lzt 720 0011 r1a 2001-07-03 145 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8.10 fcu # # , # " # # 1+ ) (# # / ) (# :) ,,- ) (# " figure 72 fcu-01 table 18 optical indicators on fcu-01 label colour mode indication fault red off no fault is detected in fcu on a fault is detected in fcu operational green off fcu not operational on fcu operational epc bus fault yellow off fcu has communication with dxu on fcu has no communication with dxu fault red off no faults have been detected in fan 1 fan 1 on one or more faults have been detected in fan 1 fan 2 red off no faults have been detected in fan 2 fault on one or more faults have been detected in fan 2 fan 3 red off no faults have been detected in fan 3 fault on one or more faults have been detected in fan 3 fault red off no faults have been detected in fan 4 fan 4 on one or more faults have been detected in fan 4 146 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8.11 idm ! $/0 1 ! 2 ! 3 2 2 2 3 3 ! 2 2 3 ! 2 ! ' 2 2 2 ! 2 4 #'3 2 3 3 + 3 $/& 0 & 2 2 2 2 / b ) 5 1 8 a 1 8 8 a figure 73 idm-01 table 19 optical indicator on idm-01 label colour mode indication opererational green off idm is not operational on idm is operational the circuit breakers on the idm provides +24 v dc to the different units. all circuit breakers can either be in an on or off position. the circuit breakers turn off automatically when a fault is detected, they can also be switched off manually. en/lzt 720 0011 r1a 2001-07-03 147 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// optical indicators and switches 8.12 psu " !" 8*&5 ! 339 !" !" figure 74 psu table 20 optical indicators on psu label colour mode indication fault red off no fault is detected in psu on a fault is detected in psu operational green off psu is not operational on psu is operational epc bus fault yellow off psu has communication with dxu on psu has no communication with dxu 8.13 rbs status panel " . ) : 1 ) ) ) 8 . . $ 3+ . ): 1) ))8.. $3+ figure 75 rbs status panel table 21 optical indicators on rbs status panel label colour mode indication rbs fault yellow off no faults are detected in rbs on one or more faults are detected in rbs 148 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance external alarm yellow off no external alarms are active on one or more external alarms are active battery mode yellow off no battery power used on battery power supply fully or partly used 8.14 tma cm / " figure 76 tma cm table 22 optical indicators on tma cm label colour mode indication fault red off no fault is detected in tma cm on a fault is detected in tma cm operational green off tma cm is not operational on tma cm is operational 1 green off tma 1 is not operational on tma 1 is operational 2 green off tma 2 is not operational on tma 2 is operational 3 green off tma 3 is not operational on tma 3 is operational 4 green off tma 4 is not operational on tma 4 is operational 5 green off tma 5 is not operational on tma 5 is operational 6 green off tma 6 is not operational tma oper. on tma 6 is operational en/lzt 720 0011 r1a 2001-07-03 149 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance this page is intentionally left blank 150 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance 9 preventive maintenance during normal use, parts of the rbs become dirty or worn. to prevent a fault within the rbs, regularly scheduled cleaning or replacement of parts is necessary. this chapter gives the information needed to perform preventive maintenance. the process causes a minimum of interruption to operation of the rbs. 9.1 preventive maintenance process -! $0 0 0 $ $ # $# + $ + $ $ % figure 77 preventive maintenance process 9.2 determining preventive maintenance intervals use the table that follows to determine which routines must be performed. always perform the routines in the same order as they appear in the table. the interval between inspections at each rbs site may vary depending upon the environmental conditions found there. en/lzt 720 0011 r1a 2001-07-03 151 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance table 23 preventive maintenance intervals action period antenna system maintenance once a year battery maintenance (1) every ve years replace batteries (1) (2) every ve years replace fans every ten years replace door lter (3) every ve years checklist "before leaving the site" every site visit (1) it is recommended that batteries be purchased locally. refer to information supplied by the manufacturer for the correct inspection and replacement interval. (2) this procedure is included in the "battery maintenance procedure" (3) inspect the door lter every site visit. 9.3 maintaining antenna systems the checklist that follows is designed for a visual inspection of the antenna system. except for the checklist provided, there are no preventive maintenance routines for the antenna system. there is no performance check for the antenna system. warning some working areas involve the risk of accidents caused by falling objects. note: local safety regulations may require that any maintenance on antennas, or antenna towers, be performed by an individual who has been certi ed to climb antenna poles and masts. antenna access 1. open the rbs cabinet to inspect the rf cables. 2. go to the checklist. antenna checklist the answer to all 19 questions must be "yes". when the checklist has been completed proceed to the section correct faults if the answer to any question is "no". 152 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance table 24 antenna checklist item n/a 1 yes no 1 are poles in safe condition, that is, free of cracks, not bent or loose? 2 is lightning protection secure and functional? 3 is the tma rmly mounted and in good condition? 4 do all cables have markers? 5 are cables secured to poles (approximately once every 0.6 meters)? 6 are the cable seals at the entry point into the cabinet in good condition? 7 are all cables free from abrasions, cuts and cracks? 8 are all cable connector seals in good condition? 9 are all cable ducts dry and the seals in good condition? 10 are antenna towers and legs free of corrosion? 11 are antenna towers free of bows or bends? 12 are hazard lights operational ? 13 are support pedestals free of signs of wear and/or cracks? 14 are the guy wires relatively free of corrosion? 15 are the guy wires free of signs of slipping? 16 are the guy wires free of broken strands? 17 are the antennas correctly orientated? 18 are the antennas rmly mounted? 19 is the rbs transmission path free of obstructions? (no new buildings, towers, and so on blocking it since installation.) signature: date: 1 n/a stands for not applicable. correct faults 1. only tighten loose connections, or replace rf cables in the cabinet. 2. contact the supervisor to inform them of any other faults found when performing the checklist as further repair activitis may require eld technicans trained and certi ed to climb towers. 9.4 maintaining batteries this section describes how to access the batteries, both internal and external when used. there is also a battery checklist and instructions on how to correct faults at the end of the section. en/lzt 720 0011 r1a 2001-07-03 153 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance there is no speci c performance check for the battery system for rst line maintenance. danger read safety instructions regarding handling and connecting batteries. note: it is recommended that batteries are purchased locally. refer to information supplied by the manufacturer for the correct inspection and replacement interval. caution short circuits can cause injury or damage. although the battery voltage may be low, the released power can be extremely high. battery access 1. inspect the batteries located in the bbs 2000. 2. go to the checklist. battery checklist the answer to all six questions must be "yes". when the checklist has been completed proceed to the section corret faults if any answer to question is"no". table 25 battery checklist item n/a 1 yes no 1 are the batteries and battery box free of dirt, excessive grease, oxidation and corrosion? 2 are all cables rmly connected and in good condition? 3 are the battery casings free from discoloration and deformities? 4 are the battery terminals unbent and free from excessive cuts or slices? 5 are the batteries still within their replacement date? 6 are any batteries leaking (acid)? signature: date: 154 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance 1 n/a stands for not applicable. correct faults 1. clean dirt and grease off the batteries and battery box with a mild detergent, a soft bristle brush and rags. note: all cleaning items should be purchased locally. treat all corrosion or oxidation in accordance with local procedures. 2. tighten any loose cables found, or replace them if necessary. 3. if a discolored or deformed battery is found during the inspection, replace all batteries in the same battery box at the same time. see manufacturing documentation . 4. if the battery poles show signs of excessive damage, replace both batteries in the same battery box at the same time. see manufacturing documentation . 5. if the expiry date on a battery has passed, replace all batteries in the battery box at the same time. see manufacturing documentation . 6. if the batteries have leaked acid (or are leaking), replace the batteries. see manufacturing documentation . 9.5 replacing fans note: the only preventive maintenance included in this procedure is replacement. 1. when replacement is necessary for preventive maintenance, replace all four fans: see section fans in the chapter rbs field repair 9.6 replacing door filter note: the only preventive maintenance included in this procedure is replacement. en/lzt 720 0011 r1a 2001-07-03 155 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// preventive maintenance $ + $ figure 78 location of the door lter and retaining springs 1. open the cabinet door and release one side of the four retaining springs holding the lter in place. 2. replace the door lter. attach the retaining springs and close the cabinet door. 9.7 performing concluding routines 1. before leaving the site, proceed to chapter concluding routines and complete the checklist. 156 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections 10 cable connections the cabinet cables are grouped into three cable groups: ? power cables ? opto cables ? backplane cables 10.1 power cables there are no power cables for the maintenance personnel to connect if the +24 v dc option is selected. 24 v power cables are factory connected. 230 v ac and -48 v dc power cables are pre-mounted to the cabinet. connection of the power cables to the psus is shown in gure below. ,! , " , " 1 # 6 - ! figure 79 230 v ac and -48 v dc power cables table 26 psu power connector no. product no. connects to 1to4 accu/dccu connection eld 5to8 idm panel 230 v ac power cable rpm 513 1341/02250 may substitute for the 230 v ac power cable rpm 513 1178/02250 in some cabinet variants. 10.2 opto cables cables from the cable set basic are connected as shown in gure below. en/lzt 720 0011 r1a 2001-07-03 157 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections ",, , " 1 # figure 80 opto cables (batteries not tted) cable numbers 1 - 3 should only have a single label in the centre listing the product number. the opto cables are tted to the psus, dxu and fcu in the above con guration as the factory default. two additional opto cables are connected to the cabinet from the connection eld. these additional cables are only used when external batteries are used. for possible future use, the cables have to be neatly secured. 158 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections "," , " 1 # , 1+ ( figure 81 opto cables (external batteries tted) the opto cables are tted to the psus and dxu in the "without batteries" con guration as the factory default. if batteries are to be used then a change will be needed from the factory default cabling. 10.3 backplane cables the backplane cables can be either signal (bus) or power cables. to reach the backplane cables the rus have to be removed, for example to reach the tru backplane the trus have to be removed so the tru magazine can be removed. some cables have connection to the backplane and to the front of the rus. cabinet left connection field the internal cabling to the left connector plate is routed from behind the connector plate. the connector plate must be removed to access the internal connectors and cables. en/lzt 720 0011 r1a 2001-07-03 159 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections "! ( , " .) ," 6 - ! ! , " - 6 figure 82 left connector plate at the cabinet top table 27 the internal cables are connected from behind connector no. cable product no. connects to 1 rpm 513 1110/01700 idm backplane: dc out 2-5 rpm 513 870/02250 dxu front: port a to d 6 rpm 513 1108/02660 dxu backplane: ext alarm 7 and 8 dxu front: esb 9to12 rpm 513 1811/00850 fan 1 4 13 rpm 513 1138/01700 idm backplane: fan 1-4 14 rpm 513 1409/02500 dxu front: opto td 15 rpm 982 02/200 connector 16 16 rpm 982 02/200 connector 15 17 rpm 513 1116/02500 dxu backplane: led cdu cables (power and signal cable) the cdu magazine do not have any backplane cabling. the power and signal bus are located at the front of the cdus. the power and bus cable to the cdu are the same for cdu-f and cdu-g. 160 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections ", , (# figure 83 cdu-f cables " a (# , figure 84 cdu-g cables note: this gure only shows one cdu, the table describes all the cdu power and bus cables. table 28 cdu cables connector no product no. connects to 1 rpm 513 1118/ 02130 x3 tru backplane: cdu 1 to 3 2 rpm 513 718/01400 x3 idm backplane. cdu 1 to 3 cxu cables (power and signal cable) the cxu have a number of rf cables, those are described in chapter cdu connections . en/lzt 720 0011 r1a 2001-07-03 161 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections "" , figure 85 cxu cabling table 29 cxu cables connector no. product no. connects to 1 rpm 513 1162/ 01000 idm backplane: cxu 1 dc in 2 rpm 513 1178/ 01650 tru backplane: cxu 1 tru backplane cables (power and signal cable) to access the tru backplane all 6 trus and the magazine have to be removed. " 02 3+ , " 6 - ! , " , " 6 - /- :/. 3 , 1 6 1 , " !/, :/. 3 figure 86 tru backplane cables table 30 tru backplane connector no. product no. connects to 1 rpm 513 1781/02000 dxu front:y-links 1-6 2 rpm 513 1117/02130 dxu backplane: iom 3 rpm 513 1903/01650 cxu front: iom bus 4-6 rpm 513 1118/02130 x3 cdu front: cdu bus 1-3 7 rpm 513 1781/2000 dxu front:y-links 7-12 8-13 rpm 513 1120/00700 x6 idm backplane: tru 1- 6 162 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cable connections idm backplane cables (power cables) to access the idm cables the front plate have to be removed. there are two connectors to the front plate, remove them carefully. # / , " , 6 - 02 " 1 , " 6 - ! , " 1 " 1 , 1 " - 6 " , " , , " % 0 =1 figure 87 idm cables table 31 tru backplane connector no. product no. connects to 1 rpm 513 1110/01700 cabinet connector plate: dc out 2 rpm 513 1138/01700 fcu card: fan 1-4 3 and 4 rpm 513 1120/00700 x2 tru backplane: tru 1-2 dc in 5 rpm 513 718/01400 cdu front: cdu1 bus 6 and 7 rpm 513 1120/00700 x2 tru backplane: tru 3-4 dc in 8 rpm 513 718/01400 cdu front: cdu2 bus 9 and 10 rpm 513 1120/00700 x2 tru backplane: tru 5-6 dc in 11 rpm 513 718/01400 cdu front: cdu3 bus 12 rpm 513 1162/01000 oxu front: dc in 13 rpm 513 1845/01600 dxu backplane: +24v 14 rpm 513 1114/01400 system earthing dxu backplane cables (power and signal cable) to access the dxu cables the oxu dummys, dxu and psus must be removed. en/lzt 720 0011 r1a 2001-07-03 163 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections " 3+ , " .) b,< 1 figure 88 dxu backplane cables table 32 dxu backplane connector no. product no. connects to 1 rpm 513 1116/ 02500 cabinet connection plate: led 2 rpm 513 1108/ 02660 cabinet connection plate: ext alarms 3 rpm 513 1845/ 01600 idm backplane: sys. volt 4 rpm 513 1117/ 02130 tru backplane: iom 164 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11 cdu connections the cabinet cables are grouped into cable sets and provided as a cable pack. these packs provide all the cables for the following functions: ? opto - opto cables between psus, fcu, dxu and bfus ? power - all cables related to the main input power ? cdu - all cables related to dtru, cxu and cdu note: all connectors, including attenuators and dummy loads, are to be tightened using torque wrench. see chapter tools. the new cable set modules contain all cables for any one cell, see chapter introduction for details. cables, not involving rus, are factory tted to the cabinet. all unused output ports on the cxus are to be terminated with 50 terminators. all input ports not in used (for example, transmitter ports) on the cdus are terminated with the plastic protective sleeves. these terminators and protective sleeves are supplied with the cxu. "" figure 89 terminating unused ports on cxu 11.1 inserting and extracting rus at the rear of each ru there are up to two connectors which are inserted into connectors in the magazine backplane. cdus and trus also have locating pins to assist alignment. en/lzt 720 0011 r1a 2001-07-03 165 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections "7" . $+ figure 90 rus with connectors and locating pins to insert an ru: 1. hold the unit by the upper and lower edges of the front plate and insert into the magazine. 2. install each ru by aligning the edges with the magazine rails and gently push the unit fully into the magazine. 3. secure the ru in position with the captive screws. 67"- figure 91 inserting rus to remove an ru: 1. loosen the captive screws. 166 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 2. insert the extraction tool into the slot on the unit front and turn the tool 90 on either direction. 3. carefully pull the unit forward and remove it. 7" figure 92 removing rus 11.2 cdu to connection field - general each cdu is connected to antenna sockets situated in the connection eld of the cabinet. the connection eld is situated on the top of the cabinet: ? rbs 2206 - rx and tx connectors to the antenna are directly connected to the cdu. the antenna ends of these cables are connected to rf sockets in the base or roof of the cabinet for connection to antennas. the following information describes the connection eld sockets and the cdu connections to which they are connected. cdus are numbered one to three (left to right) as they appear in the cabinet. this manual does not list all rbs 2000 con gurations, for a complete list, see: reference manual ln/lzt 720 0008 11.3 cdu to connection field rbs 2206 the antenna connection elds are located on top of cdu-f and cdu-g. en/lzt 720 0011 r1a 2001-07-03 167 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections !6 / figure 93 cdu-f layout /a (# (# , ! , # 1+ figure 94 cdu-g layout 168 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.3.1 cable set module wiring cdu-f ,"6 h 6"!"="h*,gg h 6"!,=g h 6"!,=66h*,gg h 6"!,=!g h 6"!"=,"h*gg ( ( # #, # #, , " , " , , , (# , , , figure 95 cdu-f connection to cxu and tru cable kit no: ntm 201 2826/1 en/lzt 720 0011 r1a 2001-07-03 169 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.3.2 cable set module wiring cdu-g with hybrid combiner ( ( ,"- # #, , " , " , h 6"!"="h*,gg h 6"!,="h*,gg h 6"!"=,"h*gg , (# , h 6"!,=!h*gg , #, # , figure 96 cdu-g connection to cxu and tru with hybrid combiner cable kit no:ntm 201 2825/1. 170 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.3.3 cable set module wiring cdu-g without hybrid combiner , h 6"!"="h*,gg h 6"!,=," h 6"!,= ( ( , (# ,"! , , #, # h 6"!"=,"h*,gg , " # % , figure 97 cdu-g connection to cxu and tru without hybrid combiner cable kit no: ntm 201 2824/1. en/lzt 720 0011 r1a 2001-07-03 171 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.3.4 internal cdu connections "6 # #, # #, / , , , , , , # #, # #, / , , , (# , , , # #, # #, / , , , (# , , , (# figure 98 connections between cdus 172 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.4 cdu antenna connection field rbs 2206 ,6 "*, / 8# ( 8# ( = %+ figure 99 cdu con guration key the various con gurations available for cabinets are described using the following system: in the example above, the cabinet is tted with 3 cdus, each connected to 2 trus; so there is a total of 6 trus in this case. the cdu is type cdu-f. the rf cables between each cdu and its associated trus are standardized and do not normally change. each cdu uses a set of standard rf wiring patterns for connection between each cdu and the cabinet connection field. in the gures and tables in the sections that follow, the cabinets shown are fully equipped. con gurations consisting of a part of the fully equipped cabinet are also possible to extract from the following gures and tables. 11.4.1 cdu-f antenna connection "6- / / / = figure 100 cdu-f antenna feeder connectors, rbs 2206 en/lzt 720 0011 r1a 2001-07-03 173 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.4.2 900/1800 cdu-f con gurations 3x2 cdu-f and 3x4 cdu-f ,,! figure 101 con guration scheme without tma ,- figure 102 con guration scheme with tma 174 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections table 33 3x2 cdu-f and 3x4 cdu-f cell cdu connection signal labelling tx/rx tx/rx cella: dx1 a 1 rx rx cella: rxb tx/rx tx/rx cellb: dx1 b 2 rx rx cellb: rxb tx/rx tx/rx cellc: dx1 c 2 rx rx cellc: rxb from the con guration scheme in gures above, the following con gurations can be derived: ? 1x2 cdu-f ? 2x2 cdu-f ? 1x4 cdu-f ? 2x4 cdu-f 1x8 cdu-f ,, , figure 103 con guration scheme without tma en/lzt 720 0011 r1a 2001-07-03 175 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,66 , figure 104 con guration scheme with tma table 34 1x8 cdu-f cell cdu connection signal labelling 1 tx/rx tx/rx cella: dx1 a 2 tx/rx tx/rx cella: dx2 1x12 cdu-f ,, , figure 105 con guration scheme without tma 176 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,6- , figure 106 con guration scheme with tma table 35 1x12 cdu-f cell cdu connection signal labelling 1 tx/rx tx/rx cella: dx1 a 3 tx/rx tx/rx cella: dx2 2x6 cdu-f ,", figure 107 con guration scheme without tma en/lzt 720 0011 r1a 2001-07-03 177 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,6! figure 108 con guration scheme with tma table 36 2x6 cdu-f cell cdu connection signal labelling tx/rx tx/rx cella: dx1 a 1 rx rx cella: rxb tx/rx tx/rx cellb: dx1 b 3 rx rx cellb: rxb 1x4 + 1x8 cdu-f ," , figure 109 con guration scheme without tma 178 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,6 , figure 110 con guration scheme with tma table 37 1x4+1x8 cdu-f cell cdu connection signal labelling tx/rx tx/rx cella: dx1 a 1 rx rx cella: rxb 2 tx/rx tx/rx cellb: dx1 b 3 tx/rx tx/rx cellb: dx2 1x8 + 1x4 cdu-f ," , figure 111 con guration scheme without tma en/lzt 720 0011 r1a 2001-07-03 179 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,6 , figure 112 con guration scheme with tma table 38 1x8+1x4 cdu-f cell cdu connection signal labelling 1 tx/rx tx/rx cella: dx1 a 2 tx/rx tx/rx cella: dx2 tx/rx tx/rx cellb: dx1 b 3 rx rx cellb: rxb 11.4.3 cdu-g antenna connection "6! /a /a /a = =, figure 113 cdu-g antenna feeder connectors, rbs 2206 180 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 11.4.4 900/1800 cdu-g con gurations 3x2 cdu-g and 3x4 cdu-g ,," , , , figure 114 con guration scheme without tma ,- , , , figure 115 con guration scheme with tma en/lzt 720 0011 r1a 2001-07-03 181 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections table 39 3x2 cdu-g and 3x4 cdu-g cell cdu connection signal labelling tx/rx1 tx/rx cella: dx1 a 1 tx/rx2 tx/rx cella: dx2 tx/rx1 tx/rx cellb: dx1 b 2 tx/rx2 tx/rx cellb: dx2 tx/rx1 tx/rx cellc: dx1 c 3 tx/rx2 tx/rx cellc: dx2 from the con guration in the gure above, the following con gurations can be derived: ? 1x2 cdu-g ? 2x2 cdu-g ? 1x4 cdu-g ? 2x4 cdu-g 1x8 cdu-g ,,6 , , figure 116 con guration scheme without tma 182 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,"" , , figure 117 con guration scheme with tma table 40 1x8 cdu-g cell cdu connection signal labelling tx/rx1 tx/rx cella: dx1 1 tx/rx2 tx cella: tx1 tx/rx1 tx/rx cella: dx2 a 2 tx/rx2 tx cella: tx2 1x12 cdu-g ,,- " , , figure 118 con guration scheme without tma en/lzt 720 0011 r1a 2001-07-03 183 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections ,-, , , " figure 119 con guration scheme with tma table 41 1x12 cdu-g cell cdu connection signal labelling tx/rx1 tx/rx cella: dx1 1 tx/rx2 tx cella: tx1 tx/rx1 tx cella: tx2 2 tx/rx2 tx cella: tx3 tx/rx1 tx/rx cella: dx2 a 3 tx/rx2 tx cella: tx4 184 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections 2x6 cdu-g ,, , , , figure 120 con guration scheme without tma ,-" , , , figure 121 con guration scheme with tma table 42 2x6 cdu-g cell cdu connection signal labelling tx/rx1 tx/rx cella: dx1 1 tx/rx2 tx/rx cella: dx2 a tx/rx1 tx cella: tx1 2 tx/rx2 tx cella: tx2 tx/rx1 tx/rx cella: dx1 b 3 tx/rx2 tx/rx cella: dx2 en/lzt 720 0011 r1a 2001-07-03 185 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// cdu connections this page is intentionally left blank 186 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary 12 glossary this glossary lists abbreviations and acronyms used in texts dealing with rbs 2000. some basic terms and acronyms needed for cross-references are included in the list. in the rbs manuals, terminology de ned by gsm is used together with terms related to ericsson gsm system products. terms and abbreviations an arrow -> is used to indicate a reference to another entry in this list . abis gsm interface standard de ning attributes of the communication between bsc and bts ac alternating current acb alarm collection board accu alternating current connection unit a/d converter analog to digital converter air conditioner one version of the climate unit (active cooler) ais alarm indication signal alna antenna low noise ampli er ao application object arae antenna related auxiliary equipment arfcn absolute radio frequency channel number aru active replaceable unit asic application speci c integrated circuit astra asic in the tru at alphanumeric terminal atru adaptive transceiver unit atsr air time slot resource balun balance and unbalance transformer batt battery bb battery box bbs battery backup stand en/lzt 720 0011 r1a 2001-07-03 187 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary bcch broadcast control channel downlink only broadcast channel for broadcast of general information at a base station, on a base station basis. bdm battery distribution module the bdm is an idm with a battery and a local processor. ber bit error rate bfu battery fuse unit bias-ic bias injector bm denotes a full rate traf c channel bpc basic physical channel denotes the air interface transport vehicle formed by repetition of one time slot on one or more radio frequency channels. bs base station bsc base station controller gsm network node for control of one or more btss. bscsim base station controller simulator bss base station system gsm network logical unit comprising one bsc and one or more btss. bts base transceiver station gsm network unit operating on a set of radio frequency channels in one cell. burst a portion of digital information, the physical content, that is transferred within the time interval of one time slot. cabinet the physical housing of a base station cbch cell broadcast channel this is a downlink only channel used by the gsm de ned smscb function. ccch common control channel channel combining the following common control channels: 188 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary pch paging channel rach random access channel agch access grant channel ccu climate control unit cdu combining and distribution unit ce conformite europe enne cell an area of radio coverage identi ed by the gsm network by means of the cell identity cf central functions channel the common term channel denotes the virtual connection, consisting of physical and logical channels between bss and ms, during a call in progress. -> logical channel -> physical channel channel combination a physical channel on an air interface carries a de ned set of logical channels. channel group a channel group is a group of dedicated logical channels to a speci c ms. cm control module (for tma) cmd digital radio communication tester cmru central main replaceable unit. main ru. the rbs is physically connected to the base station controller (bsc) via the cmru. there is only one cmru in each rbs. cnu combining network unit compr compressor con lapd concentrator lapd concentration is used to reduce the number of required physical links between the bsc and bts. con g con guration co-siting co-siting is to operate the radio base station in gsm together with the radio base station in total access communication system (tacs) or nordic en/lzt 720 0011 r1a 2001-07-03 189 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary mobile telephone system (nmt) on the same site by sharing common equipment. cpu central processing unit csa canadian standards association cses consecutive severely errored second csu channel service unit cu combining unit (ru in cdu_d) cxu con guration switch unit dannie asic in the tru db database dc direct current dcch dedicated control channel dedicated control channels carry signalling data. dccu dc connection unit ddtma dual duplex tower mounted ampli er this type needs only one combined tx/ rx feeder from the bts to the tma. >dtma >rtma >tma >bts df distribution frame dfu distribution and fuse unit dip digital path the name of the function used for supervision of the connected pcm lines. dixie asic in the tru dm degraded minute dm distribution module dmru distributed main replaceable unit if a main ru is subordinated to the cmru, it is said to be distributed. downlink signalling direction from the system to the ms dp digital path dpx duplexer 190 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary ds1 digital signal level 1 (1544 kbit/s) dsp digital signal processor dt data transcript dtma duplex tma dtma is similar to the old alna except for different characteristics. >ddtma >rtma >tma dtru double transceiver unit du distribution unit (ru in cdu-d) dx direct exchange dxc digital cross connector dxu distribution switch unit dxx ericsson cellular transmission system including nms e1 short for g.703 2048 kbit/s pcm link e-gsm extended gsm eacu external alarm connection unit ecu energy control unit ec1 external condition map class 1 ec2 external condition map class 2 edge enhanced data rate for global evolution edt electrical down tilt eeprom electrically erasable programmable read-only memory emc electro magnetic compatibility emf electromotive force emi electromagnetic interference env environmental es errored second esb external synchronization bus esd electrostatic discharge eso ericsson support of ce en/lzt 720 0011 r1a 2001-07-03 191 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary ext external facch fast associated control channel main signalling channel in association with a tch. fcc federal communications commission fcch frequency correction channel fcomb filter combiner fcu fan control unit fdl facility data link fer frame erasure ratio fiu fan interface unit fs function speci cation fsc field support centre fu filter unit (ru in cdu-d) fud filter unit with duplexer (ru in cdu-d) fxu future expansion unit g01 mo model for rbs 200 g12 mo model for rbs 2000 g.703 ccitt standard for transmission gprs general packet radio services gsm global system for mobile communications international standard for a tdma digital mobile communication system. originally, gsm was an abbreviation for group special mobile, which is a european mobile telecommunication interest group, established in 1982. hcomb hybrid combiner hdlc high level data link control hdsl high bit rate digital subscriber line heat exchanger one version of the climate unit heu heat exchanger unit hlin high level in 192 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary hlout high level out hms heat management system hum humidity hw hardware hwu hardware unit an hwu consists of one or more ses. an hwu is a functional unit within the rbs. the hwu is either active (equipped with a processor) or passive (without processor). ic integrated circuit id identi cation idb installation data base idm internal distribution module iec international electric commission imsi international mobile subscriber identity init initial int internal iog input/output group iom internal operation and maintenance bus ir infrared is interface switch iwd interwork description i1a internal fault map class 1a i1b internal fault map class 1b i2a internal fault map class 2a jtc joint technical committee lapd link access procedures on d-channel lapd is the data link layer (layer 2) protocol used for communication between the bsc and the bts on the abis interface. abis layer 2 is sometimes used synonymously with lapd. en/lzt 720 0011 r1a 2001-07-03 193 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary lbo line build out led light emitting diode llb line loop back lna low noise ampli er local bus the local bus offers communication between a central main ru (dxu) and distributed main rus (tru and ecu). local mode when the ru is in ru mode local it is not prepared for bsc communication. local/remote switch using the local/remote switch, an operator orders the ru to enter local or remote mode. lof loss of frame logical channel a logical channel represents a speci ed portion of the information carrying capacity of a physical channel. gsm de nes two major categories of logical channels: tchs traf c channels, for speech or user data cchs control channels, for control signalling. -> physical channel -> channel combination logical ru a unit which can be referred to, but is not a single physical unit. there are three different kinds of logical rus: 1. buses 2. antennas 3. environment los loss of signal mac medium access controller magazine a magazine is a reserved space in the cabinet, which may hold one or more rus. main ru a main replaceable unit is a replaceable unit that contains one or more processors, to which software can be downloaded from the bsc. mhs modi cation handling system 194 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary ericsson trouble report database mmi man-machine interface mo managed object mr measurement receiver ms mobile station msc mobile services switching centre gsm network unit for switching, routing and controlling calls to and from the public switched telephone network (pstn) and other networks. mstp mobile station test point multidrop two or more rbss are connected in a chain to the same transmission system. all the relevant timeslots are dropped out by each rbs. (this function is sometime called cascading.) nebs network equipment building system nms ericsson network management system in dxx nominal power the nominal power is the power level de ned when con guring the transceiver. n terminal neutral terminal in a ac mains connection o&m operation and maintenance general term for activities such as con guration, utilization of channels (frequency bands), cell planning, system supervision, hardware and software maintenance, subscriber administration, and so forth. omc operation and maintenance centre oml operation and maintenance link layer 2 communication link for operation and maintenance services on abis. omt operation and maintenance terminal the omt is a terminal that supports functions for handling the rbs on site. the terminal can be a portable pc. operation operation is the normal, everyday running of the rbs with full functionality. en/lzt 720 0011 r1a 2001-07-03 195 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary opi operational instructions ovp overvoltage protection oxu space for optional expansion p-gsm primary gsm passive ru a passive replaceable unit has a very low level of intelligence and is independent of the processor system. pcat product catalogue a web-based ordering system in ericsson s intranet. pch paging channel downlink only subchannel of ccch for system paging of mss. -> ccch pcm pulse code modulation pcu packet control unit pe terminal protective earth terminal in a ac mains connection pfwd power forward physical channel an air interface physical channel carries one or more logical channels. a physical channel uses a combination of frequency and time division multiplexing and is de ned as a sequence of radio frequency channels and time slots. -> tdma frame -> logical channel pin personal identi cation number plb payload loop back plmn public land mobile network a network, established and operated by an administration or its licensed operator(s), for the speci c purpose of providing land mobile communication services to the public. it provides communication possibilities for mobile users. for communication between mobile and xed users, interworking with a xed network is necessary. ppe personal protective equipment 196 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary prefl power re ected psu power supply unit pwu power unit rach random access channel uplink only subchannel of ccch for ms request for allocation of a dedicated channel. -> ccch rai remote alarm indication ram random access memory rber radio bit error ratio rbs radio base station all equipment forming one or more ericsson base stations. ->bts rcb radio connection box rd receive data remote mode when the ru is in ru mode remote, a link is established between the bcs and the central main ru. rf radio frequency rfch radio frequency channel a radio frequency carrier with its associated bandwidth. rftl radio frequency test loop rlc repair logistic centre r-state release state rs232 american standard for term/modem interconnection rtma receiver tma rtma has no duplexers. it is used for ampli cation of the rx signal. >ddtma >dtma >tma ru replacement unit en/lzt 720 0011 r1a 2001-07-03 197 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary an ru consists of one or more hwus. an ru may be replaced by another ru of the same type. the ru is the smallest unit that can be handled on site. rx receiver rx1 receiver antenna branch 1 rx2 receiver antenna branch 2 rxa receiver antenna branch a rxb receiver antenna branch b rxd receiver divider rxda receiver divider ampli er rxlev measure of signal strength as de ned in gsm 05.08:8.1.4 rxqual measure of signal quality as de ned in gsm 05.08:8.2.4 sacch slow associated control channel sch synchronization channel sdcch stand alone dedicated control channel main dedicated signalling channel on the air interface, mainly used for call locating and establishment. scu switching and combining unit se supervised entity ses severely errored second sig signalling sim subscriber identity module sms short message service (point to point) a short message, up to 160 alphanumeric characters long, can be sent to or from an ms (point to point). so service object ss swedish standard sub-ru a sub-replaceable unit is always connected to a superior main ru. this connection is used for example for 198 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary retrieval of the ru identity. a sub-ru normally does not have a processor. note that an ru with a processor, which cannot be loaded, is classi ed as a sub-ru. svs system voltage sensor sw software swr standing wave ratio sync synchronous t1 transmission facility for ds1 (1544 kbit/s) ta timing advance a signal sent by the bts to the ms which the ms uses to advance its timing of transmissions to the bts to compensate for propagation delay. tc transaction capabilities tch traf c channel the traf c channels carry either encoded speech or user data. tch sig traf c channel signalling td transmit data tdma time division multiple access multiplexing of several channels in a common frequency band. each channel is assigned a certain time division, a time slot. tdma frame gsm air interface time frame comprising eight time slots tdr time domain re ectometer tei terminal endpoint identi er tei is an identi cation code carried by a lapd frame as a terminal connection endpoint within a service access point (sap). tems test mobile station tf timing function tg transceiver group en/lzt 720 0011 r1a 2001-07-03 199 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// glossary timing bus the timing bus carries air timing information from the timing unit in the dxu to the trus. tm transport module the transport module is non-rbs equipment belonging to the transport network. tma tower mounted ampli er there are three types of tmas: dtma, rtma and ddtma. >dtma >rtma >ddtma tma cm tower mounted ampli er control module tn timeslot number tn o&m transport network operation and maintenance (in general) tora asic in the tru tra transcoder rate adapter the tra unit performs transcoding of speech information and rate adaption of data information. tracy asic in the tru trs transceiver system tru transceiver unit trx transceiver trxc transceiver controller ts time slot a 0.577 ms period (tdma frame subunit) corresponding to 156.25 raw bits of information. the eight time slots of each tdma frame are numbered 0...7. -> burst tt total time tu timing unit tx transmitter txa transmitter antenna a txb transmitter antenna b 200 (201) en/lzt 720 0011 r1a 2001-07-03 ? ericsson radio systems ab all rights reserved free datasheet http:// glossary txbp transmitter bandpass lter uas unavailable seconds ul underwriter laboratories uplink signalling direction from the ms to the system ups uninterrupted power supply vco voltage controlled oscillator vswr voltage standing wave ratio rf signal measure. the quotient between transmitted and re ected voltage. x-bus the x-bus carries transmit air data frames between transceivers. y-link the interface between the dxu and each dsp system in core based trus en/lzt 720 0011 r1a 2001-07-03 201 (201) ? ericsson radio systems ab all rights reserved free datasheet http:// free datasheet http:// !""# free datasheet http:// free datasheet http:// en/lzt 720 0012 r1a ? ericsson radio systems ab 1 (59) 2001-06-06 - all rights reserved - free datasheet http:// this page is intentionally left blank 2 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// spare parts catalogue ? ericsson radio systems ab - all rights reserved - en/lzt 720 0012 r1a ? ericsson radio systems ab 3 (59) 2001-06-06 - all rights reserved - free datasheet http:// spare parts catalogue due to continued progress in methodology, design and manufactoring the contents of this document are subject to revision without notice. 4 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// releasehistory .........................................8 generalinformation.......................................9 ! " # $ %% basicunits............................................13 900mhzunits..........................................15 1800mhzunits .........................................17 1900mhzunits .........................................19 !& " # $ % basicunits............................................23 cabinetparts...........................................25 commoncables.........................................27 ' ()" miscellaneousparts.......................................31 accu/dccu/vdc-filter . . ...................................33 cabinetparts...........................................35 cnuconnections.........................................37 cables...............................................39 coaxial cables cdu-g without hybrid .............................43 coaxial cables cdu-g with hybrid . ..............................45 coaxial cables cdu-f. . . ...................................47 dummies.............................................49 packing..............................................51 * + ,- & . / , en/lzt 720 0012 r1a ? ericsson radio systems ab 5 (59) 2001-06-06 - all rights reserved - free datasheet http:// this page is intentionally left blank 6 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// preface this catalogue is a complement to the maintenance manual and provides the information necessary to order replaceable parts. this information is useful for the general planning of a maintenance organ- isation and in building up a spare parts stock. the main target groups are: ? field technichians technical administrators 0 1" the user documentation for the rbs 2206 consists of customer manuals divided up to suit different process events. the contains the following information for each manual: short description recommended target group product number for more information about the rbs 2000 customer documentation library, see: en/lzt 720 0012 r1a ? ericsson radio systems ab 7 (59) 2001-06-06 - all rights reserved - free datasheet http:// preface 2 in addition to editorial changes, such as corrections of spelling, grammar and layout, the following changes have been made for each release. only the three last r-states are listed below. 8 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// spare parts philosophy for rbs 2000 the specifying and classifying of spare parts is done during the service preparation process which is a part of the industrialization process. the result is a spare part list containing three classes of spare parts: recommended for customer stock. intended to be replaced on site and intended to be repaired at ericsson repair center or by the local service organisation (code = u) recommended for customer stock. intended to be replaced on site or at local shop and intended to be disposed after consumption (code = r). not recommended for customer stock. the parts are available when needed (code = a). the spare parts catalogue is adapted to this structure. the dimensioning and recommendation of spare parts will not follow the principle one-of-each- board-in-use unless the customer expressly so insists. the dimensioning and recommendation of spare part stocks is and will be done with a computer-based calculation model for bts equipment. the tool is working with the parameters: product reliability (mtbf) spare part delivery lead time or repair turn around time. chosen service level (spare part management). the spare part structure. quantity of each unit in operation to be supported by the specific stock. the probability of shortage. . the catalogue is divided into separate chapters, depending on recommendations (classifications). position numbers put in brackets ( ) are associated parts, not necessary shown in illustrations. position numbers with letters, like 3a, 3b are alternative products. new products are indicated by a #-sign in front of the position number. parts without product number may be shown on illustrations, but are not recommended for customer stock, or may be included in a spare parts set (and not separate orderable). if a reference to another chapter is given, more information will be found there. en/lzt 720 0012 r1a ? ericsson radio systems ab 9 (59) 2001-06-06 - all rights reserved - free datasheet http:// spare parts philosophy for rbs 2000 ' ( 3 please use the regional ericsson company, else: ericsson radio systems ab sg/era/gv/dp customer support services, strategic supply management s-164 80 stockholm fax: +46 8 751 4176 0 ) ( 3 please use the regional logistics center specified in the system services contract with the local ericsson company. ' 3 use the product no. ...... seen at the bottom of this page. can order spare parts catalogues (or other manuals according to the library overview), from the same address as for spare parts, above. (within the ericsson company ) can always find the latest version of the catalogue on the intranet address: $ comments or questions regarding information in this catalogue should be addressed to: spare parts documentation, telefax: or as e-mail to can make a mhs trouble report on the catalogue ? s product no. and r-state seen at the bottom of this page. 10 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (repairable) spare parts for customer stock ! " # $ (" all parts in this chapter have the internal code = u. these parts recommended for customer stock, areintendedtobereplacedonsiteandintendedtoberepairedatanericssonrepaircentreorbythe local service organisation it is only possible to order new repairable parts as long as serial production continues. when produc- tion ceases these parts can only be sent for repair. en/lzt 720 0012 r1a ? ericsson radio systems ab 11 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (repairable) spare parts for customer stock 12 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (repairable) spare parts for customer stock 4 &" & 0 1 kry 101 1856/1 unit cxu 900/1800mhz 2 boe 602 14/1 functional unit dxu-21 3 bml 231 202/1 power supply unit psu230 1000w +24vdc fc opto 4 bmr 960 014/1 dc/dc-converter psu48 1200w, -48/+24vdc fc en/lzt 720 0012 r1a ? ericsson radio systems ab 13 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (repairable) spare parts for customer stock 14 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (repairable) spare parts for customer stock 25 4 &" & 0 1 krc 131 1002/1 transceiver dtru; gmsk 2 bfl 119 147/1 combiner unit cdu-f 3 bfl 119 142/1 combiner unit e-gsm / cdu-g en/lzt 720 0012 r1a ? ericsson radio systems ab 15 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (repairable) spare parts for customer stock 16 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (repairable) spare parts for customer stock %6 25 4 &" & 0 1 krc 131 1003/1 transceiver dtru; gmsk 2 bfl 119 149/1 combiner unit cdu-f 3 bfl 119 143/1 combiner unit cdu-g en/lzt 720 0012 r1a ? ericsson radio systems ab 17 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (repairable) spare parts for customer stock 18 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (repairable) spare parts for customer stock % 25 4 &" & 0 1 krc 131 1004/1 transceiver dtru; gmsk 2 kry 112 54/1 damper asu 3 bfl 119 153/1 combiner unit cdu-g en/lzt 720 0012 r1a ? ericsson radio systems ab 19 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (repairable) spare parts for customer stock this page is intentionally left blank 20 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (not repairable) spare parts for customer stock !& " # $ (" all parts in this chapter have the internal code = r. these parts are recommended for customer stock, and are intended to be replaced on site, or at a local shop and are intended to be disposed of after consumption. en/lzt 720 0012 r1a ? ericsson radio systems ab 21 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (not repairable) spare parts for customer stock ! " ! # $ # % & ' 22 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (not repairable) spare parts for customer stock 4 &" & 0 1 sxa 134 331/1 filter set complete package. 2 bmg 980 06/1 distribution unit idm unit including psu cables 3 sdk 107 881/1 printed board tma-cm 01 4 kdr 109 61/964 microcircuit flash ata 64.2m 5.5v 3.3v i en/lzt 720 0012 r1a ? ericsson radio systems ab 23 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (not repairable) spare parts for customer stock 24 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (not repairable) spare parts for customer stock " &" & 0 1 roa 219 5313/1 printed board assemb tru backplane 2 roa 219 5314/1 printed board assemb dxu backplane 3 roa 117 8126/2 printed board assemb fcu 4 fan 4bkv301216/77 fan diagonal,dia. 171,5*51 24 vdc en/lzt 720 0012 r1a ? ericsson radio systems ab 25 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (not repairable) spare parts for customer stock ! 26 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// recommended (not repairable) spare parts for customer stock " &" & 0 1 rpm 513 852/00160 connection cable opto 2 rpm 513 852/00250 connection cable opto en/lzt 720 0012 r1a ? ericsson radio systems ab 27 (59) 2001-06-06 - all rights reserved - free datasheet http:// recommended (not repairable) spare parts for customer stock this page is intentionally left blank 28 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts ' ()" (" all parts in this chapter have the internal code = a. these parts are not recommended for customer stock. the parts are available upon request and the lead time may be longer. en/lzt 720 0012 r1a ? ericsson radio systems ab 29 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts " !# ! 30 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts &" & 0 1 roa 117 2966/1 printed board assemb led-ib 2 kty 901 05/1 accessories transmission adapter 3 kry 101 1587/1 accessories bias injector 900/1800 mhz 4 rpm 113 5445/1 cable with connector bias cable 5 rpm 113 5447/1 cable with connector connection plate included 6 rpm 513 904/02160 cable signal esb 7 ntz 112 85/at01 spare parts set adapter kit en/lzt 720 0012 r1a ? ericsson radio systems ab 31 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts ()&*&+,##-&#*& $*& (*. " $*& (*. " / 32 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts (47047809 &" & 0 1 bmg 980 07/1 accu cables to psu included 2 bmg 980 07/2 dccu cables to psu included 3 kfe 101 1145/1 filter unit cables to idm included en/lzt 720 0012 r1a ? ericsson radio systems ab 33 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts 34 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts " &" & 0 1 bfl 119 406/1 subrack subrack cdu 2 bfl 119 407/1 subrack subrack tru 3 bfl 119 408/1 subrack subrack dxu 4 sxk 107 8304/1 door door gsm 5 sxa 134 216/1 spring filter spring 6 sxk 107 5063/1 lock lock system door 7 sxk 107 8759/1 lock lock assembly en/lzt 720 0012 r1a ? ericsson radio systems ab 35 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts 36 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts &4 &" & 0 1a kry 101 1829/1 cnu 900mhz 1b kry 101 1830/1 cnu 1800mhz 2a rpm 213 1013/1 cable with connector 2b rpm 213 1025/1 cable with connector 3 rpm 213 1033/1 cable with connector 4 rpm 213 1034/1 cable with connector 5 rpm 213 1035/1 cable with connector 6a rny 101 23/01 accessories n-coax cover 900mhz 6b kry 101 1883/1 accessories n-coax cover 1800mhz en/lzt 720 0012 r1a ? ericsson radio systems ab 37 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts "# $%& '( 38 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts " &" & 0 1 rpm 513 870/02250 cable with connector 120 ohm/l=2.25 m/bus g703/dxu11 2 rpm 513 1110/01700 connection cable connect.cable +24v 3 rpm 513 1410/02500 optical fibre cable optical fibre cable 4 rpm 513 1409/02500 optical fibre cable optical fibre cable 5 rpm 513 1138/01700 power cable power cable 6 rpm 513 1116/02500 signalling cable led-cable gsm syst 7 rpm 513 1108/02660 connection cable ext-larm gsm syst 8 rpm 982 02/200 opt.cable w. connect l=200 mm en/lzt 720 0012 r1a ? ericsson radio systems ab 39 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts $%& )*+, -*% $%& '( $%& ! ! 40 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts ! # &" & 0 1 rpm 513 1781/02000 cable with connector y-link cable gsm syst 2 rpm 513 1117/02130 signalling cable iom-bus gsm syst 3 rpm 513 1120/00700 power cable +24v gsm syst tru idm 4 rpm 513 1162/01000 power cable power cable 5 rpm 513 718/01400 power cable power cable +24v 6 rpm 513 1845/01600 cable with connector +24v idm fxu 1,2,3,4 7 rpm 513 1118/02130 signalling cable cdu-bus cable 8 rpm 513 1178/01650 power cable power cable en/lzt 720 0012 r1a ? ericsson radio systems ab 41 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts ! .//0 42 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts / " 049 + " &" & 0 1 rpm 513 1783/00390 coaxial cable coax.cable cdu-tru/rxa 2 rpm 513 1782/00230 coaxial cable coaxial cable 3 rpm 513 1782/00410 coaxial cable coaxial cable 4 rpm 513 1783/00210 coaxial cable coax.cable cdu-tru/rxa 9 rpm 513 1783/00230 coaxial cable coax.cable cdu-tru/rxa en/lzt 720 0012 r1a ? ericsson radio systems ab 43 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts ! 44 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts / " 049 + " &" & 0 1 rpm 513 1783/00390 coaxial cable coax.cable cdu-tru/rxa 4 rpm 513 1783/00210 coaxial cable coax.cable cdu-tru/rxa 5 rpm 513 1782/00310 coaxial cable coaxial cable 6 rpm 513 1782/00070 coaxial cable coaxial cable 9 rpm 513 1783/00230 coaxial cable coax.cable cdu-tru/rxa en/lzt 720 0012 r1a ? ericsson radio systems ab 45 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts ! 46 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts / " 049: &" & 0 1 rpm 513 1783/00390 coaxial cable coax.cable cdu-tru/rxa 3 rpm 513 1782/00410 coaxial cable coaxial cable 4 rpm 513 1783/00210 coaxial cable coax.cable cdu-tru/rxa 7 rpm 513 1782/00550 coaxial cable coaxial cable 8 rpm 513 1782/00700 coaxial cable coaxial cable 9 rpm 513 1783/00230 coaxial cable coax.cable cdu-tru/rxa 10 rpm 513 1782/00460 coaxial cable coaxial cable en/lzt 720 0012 r1a ? ericsson radio systems ab 47 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts 48 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts 0 &" & 0 1 sxk 107 5047/1 dummy unit cdu-dummy 2 sxk 107 9163/1 dummy unit tru dummy 3 sxk 107 9314/1 dummy unit psu-dummy 4 sxk 107 5030/1 dummy unit oxu 6 te gsm 5 sxk 107 5029/1 dummy unit oxu 5 te gsm en/lzt 720 0012 r1a ? ericsson radio systems ab 49 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts this page is intentionally left blank 50 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// other available parts $ &" & 0 rtk 993 5265/2 packing set dxu rtk 993 5519 packing set dtru rtk/bfl 119 142/1 packing set cdu-g rtk/bfl 119 147/1 packing set cdu-f rtk/kry 101 1856/1 packing set cxu rtk/bml 231 201 packing set psu en/lzt 720 0012 r1a ? ericsson radio systems ab 51 (59) 2001-06-06 - all rights reserved - free datasheet http:// other available parts this page is intentionally left blank 52 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// replaced and withdrawn parts * + (" this chapter shows replaced or withdrawn products due to continous improvement in design and production methods, some parts are changed. this is the only place in this catalogue release where you still can find product numbers shown in previous catalogues. in this way we manage to keep the numerical index as a list of orderable spare parts. en/lzt 720 0012 r1a ? ericsson radio systems ab 53 (59) 2001-06-06 - all rights reserved - free datasheet http:// replaced and withdrawn parts this page is intentionally left blank 54 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// replaced and withdrawn parts ! " # en/lzt 720 0012 r1a ? ericsson radio systems ab 55 (59) 2001-06-06 - all rights reserved - free datasheet http:// replaced and withdrawn parts this page is intentionally left blank 56 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// numerical index & . / bfl119142/1 ...................................................... 15 bfl119143/1 ...................................................... 17 bfl119147/1 ...................................................... 15 bfl119149/1 ...................................................... 17 bfl119153/1 ...................................................... 19 bfl119406/1 ...................................................... 35 bfl119407/1 ...................................................... 35 bfl119408/1 ...................................................... 35 bkv301216/77 .......................... .......................... 25 bmg98006/1 ...................................................... 23 bmg98007/1 ...................................................... 33 bmg98007/2 ...................................................... 33 bml231202/1...................................................... 13 bmr960014/1...................................................... 13 boe60214/1....................................................... 13 kdr10961/964 .......................... .......................... 23 kfe1011145/1........................... .......................... 33 krc1311002/1 .......................... .......................... 15 krc1311003/1 .......................... .......................... 17 krc1311004/1 .......................... .......................... 19 kry1011587/1 .......................... .......................... 31 kry1011829/1 .......................... .......................... 37 kry1011830/1 .......................... .......................... 37 kry1011856/1 .......................... .......................... 13 kry1011883/1 .......................... .......................... 37 kry11254/1....................................................... 19 kty90105/1....................................................... 31 ntz11285/at01..................................................... 31 rny10123/01...................................................... 37 roa1172966/1 .......................... .......................... 31 roa1178126/2 .......................... .......................... 25 roa2195313/1 .......................... .......................... 25 roa2195314/1 .......................... .......................... 25 rpm1135445/1 .......................... .......................... 31 rpm1135447/1 .......................... .......................... 31 rpm2131013/1 .......................... .......................... 37 rpm2131025/1 .......................... .......................... 37 rpm2131033/1 .......................... .......................... 37 rpm2131034/1 .......................... .......................... 37 rpm2131035/1 .......................... .......................... 37 en/lzt 720 0012 r1a ? ericsson radio systems ab 57 (59) 2001-06-06 - all rights reserved - free datasheet http:// numerical index rpm5131108/02660................................................... 39 rpm5131110/01700................................................... 39 rpm5131116/02500................................................... 39 rpm5131117/02130................................................... 41 rpm5131118/02130................................................... 41 rpm5131120/00700................................................... 41 rpm5131138/01700................................................... 39 rpm5131162/01000................................................... 41 rpm5131178/01650................................................... 41 rpm5131409/02500................................................... 39 rpm5131410/02500................................................... 39 rpm5131781/02000................................................... 41 rpm5131782/00070................................................... 45 rpm5131782/00230................................................... 43 rpm5131782/00310................................................... 45 rpm5131782/00410................................................... 43 rpm5131782/00410................................................... 47 rpm5131782/00460................................................... 47 rpm5131782/00550................................................... 47 rpm5131782/00700................................................... 47 rpm5131783/00210................................................... 45 rpm5131783/00210................................................... 43 rpm5131783/00210................................................... 47 rpm5131783/00230................................................... 45 rpm5131783/00230................................................... 47 rpm5131783/00230................................................... 43 rpm5131783/00390................................................... 43 rpm5131783/00390................................................... 45 rpm5131783/00390................................................... 47 rpm5131845/01600................................................... 41 rpm513718/01400......................... ......................... 41 rpm513852/00160......................... ......................... 27 rpm513852/00250......................... ......................... 27 rpm513870/02250......................... ......................... 39 rpm513904/02160......................... ......................... 31 rpm98202/200.......................... .......................... 39 rtk9935265/2........................... .......................... 51 rtk9935519....................................................... 51 rtk/bfl119142/1 ......................... ......................... 51 58 (59) ? ericsson radio systems ab en/lzt 720 0012 r1a - all rights reserved - 2001-06-06 free datasheet http:// numerical index rtk/bfl119147/1 ......................... ......................... 51 rtk/bml231201.................................................... 51 rtk/kry1011856/1 .................................................. 51 sdk107881/1...................................................... 23 sxa134216/1...................................................... 35 sxa134331/1...................................................... 23 sxk1075029/1 .......................... .......................... 49 sxk1075030/1 .......................... .......................... 49 sxk1075047/1 .......................... .......................... 49 sxk1075063/1 .......................... .......................... 35 sxk1078304/1 .......................... .......................... 35 sxk1078759/1 .......................... .......................... 35 sxk1079163/1 .......................... .......................... 49 sxk1079314/1 .......................... .......................... 49 en/lzt 720 0012 r1a ? ericsson radio systems ab 59 (59) 2001-06-06 - all rights reserved - free datasheet http:// . free datasheet http:// |
Price & Availability of RBS2206
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |